2022 Kawasaki KLR650 ABS Meter Instruments
Meter Instruments
- Fuel Gauge
- Clock
- Speedometer
- Left Meter Button
- Multifunction Display
- Odometer
- Trip Meter A/B
- Right Meter Button
When the ignition switch is turned on, all LCD functions are shown for a few seconds, then the multifunction meter turns to operational mode.
Indicators
- Left Turn Signal Indicator (Green)
- Battery Warning Indicator
- Coolant Temperature Warning Indicator
- Right Turn Signal Indicator (Green)
- N Neutral Indicator (Green)
- High Beam Indicator (Blue)
- Engine Warning Indicator (Yellow)
- Warning Indicator (Red)
- Fuel Level Warning Indicator
- ABS Indicator (Yellow) (ABS model)
Indicator Initial Operation
When the ignition switch is turned on, all indicators go on/off as shown in the table. If any indicator does not operate as shown, have it checked by an authorized Kawasaki dealer.
- ON: When the ignition switch is turned on.
- After a few seconds
- When the engine starts.
- Goes on.
- Goes off.
- goes off shortly after the motorcycle starts moving.
When Warning Indicators Go On or Blink
When warning indicators appear, there could be a problem with a vehicle function. Follow actions on the table after stopping the vehicle in a safe place.
- After continuous riding on a rough road.
- When the engine is started with the stand raised and the transmission engaged, the rear wheel turns.
- When accelerating so abruptly that the front wheel leaves the ground.
- When the ABS has been subjected to strong electrical interference.
- When tire pressure is abnormal. Adjust tire pressure.
- When a tire different in size from the standard size is being used. Replace with a standard size.
- When the wheel is deformed. Replace the wheel.
Other Indicators
Speedometer
- The speedometer is digital and can be set for km/h or mph.
- The unit setting can be changed ac- cording to local regulations. Make sure the unit setting (km/h or mph) is cor- rectly displayed before riding.
- Refer to the Unit Setting in the Dis- play Setting section.
Display Setting
Multifunction Display
Push the left meter button to select the items shown below. The display items are switched in the following order.
Odometer
The odometer shows the total distance. This meter cannot be reset.
NOTE
When the figures come to 999999, the display is stopped and locked.
Trip Meter
The trip meter shows the distance traveled since it was reset.
NOTE
When the trip meter reaches 9999.9 while riding, the meter resets to 0.0 and continues counting.
How to Reset
- Switch the multifunction display to the trip meter.
- Push the left meter button and hold it in until the display turns to 0.0.
Unit Setting
Display the correct speed unit ac- cording to local regulations.
- Switch the multifunction display to the odometer.
- Push the right meter button while pushing the left meter button to sWitch the speed unit.
Clock Setting
The clock can be selected from the 12h mode and 24h mode.
NOTE
When the battery is disconnected, the clock is reset to 1:00 (12h mode) or 13:00 (24h mode) and starts working again when the battery is connected.
To adjust the clock:
- Push the right meter button and hold it until shifting to the clock setting mode. The hour and minute displays starts blinking.
- Push the right meter button to select the hour or minute digits.
- Push the left meter button to adjust the hour or minute digits.
- To finish the adjustment, push the left meter button while blinking the hour and minute digits.
- Flow when pushing and holding right meter button
- Flow when pushing left meter button
- Flow when pushing right meter button
- To change 12h/24h mode:
- During blinking the hour and minute digits, push the right meter button and hold it. The current mode (12h or 24h) appears.
- Push the left meter button to select the mode.
- Push the right meter button to return to the clock adjustment.
- Flow when pushing and holding right meter button
- Flow when pushing left meter button
- Flow when pushing right meter button
Features
Fuel Gauge
The fuel in the fuel tank is shown by the number of segments displayed.
NOTE
- When the fuel tank is full, all the segments are displayed. As the fuel level in the tank goes down, the segments disappear one by one from F ful) to E (empty).
- When the fuel level warning indicator and bottom segment blink, refer to the “When Warning Indicators Go On or Blink” of Indicators in this chapter