2022 Jeep Wrangler Hard Top and Soft Top User Manual

2022 Jeep Wrangler Hard Top and Soft Top

WRANGLER TOPS

PROVIDED TOOLS

For your convenience, a tool kit is provided with your vehicle located in the center console. This kit includes the necessary tools required for the operations described in the following sections. All pieces fit into the ratchet for easy use.
NOTE
The soft top and the hardtop are to be used independently. Your vehicle warranty will not cover damage resulting from both tops being installed at the same time.

Provided Tools

1. Ratchet
2. #T50 Torx Head Driver
3. #T40 Torx Head Driver
4.  15 mm Socket

If your vehicle is equipped with a Dual Top (four-door models only), the soft top system will be provided in a separate box located in the rear of the vehicle for shipping purposes only.

LOWERING THE SOFT TOP INTO THE SUNRIDER® POSITION
Use this QR code to access your digital experience.

WARNING

• The fabric quarter windows and fabric top are designed only for protection against the elements. Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident. Remember, always wear seat belts.
• Make sure hands and fingers are clear of all pinch points when installing and removing the soft tops. The lift assist mechanism and side bows may cause serious injury if fingers or hands get caught in between.

CAUTION!

The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting, or camping supplies, and/or luggage, etc. Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.).

If the temperature is below 72°F (24°C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up. This is caused by a natural contraction of the vinyl or acrylic materials of the fabric top.
Place the vehicle in a warm area. Pull steadily on the top fabric. The vinyl will stretch back to its original size and the top can then be installed. If the temperature is 41°F (5°C) or below, do not attempt to put the top down or roll the rear or side curtains.

CAUTION!

• Do not run a fabric top through an automatic car wash. Window scratches and wax buildup may result.
• Do not lower the top when the temperature is below 41°F (5°C). Damage to the top may result.
• Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered.
• Do not fully lower the top with the windows installed. Window and top damage may occur.
• For important information on cleaning and caring for your vehicle’s fabric top Ú page 409.
• Do not use any tools (screwdrivers, etc.) to pry or force any of the clamps, clips, or retainers securing the soft top. Do not force or pry the soft top framework when opening or closing.
• Damage to the top may result.

CAUTION!

Failure to follow these cautions may cause interior water damage, stains or mildew on the top material:

• It is recommended that the top be free of water prior to opening it. Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle’s interior.
• Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle’s interior.
• The soft top must be positioned properly to ensure sealing. Improper installation can cause water to leak into the vehicle’s interior.

Four-Door Side View Components

• 1 Bow
• 2 Bow
• 3 Bow
• 4 Bow
• 5 Bow
• 6 Bow
• Front Window Retainer
• Lower Window Retainer
• Rear Quarter Window

Two Door Side View Components

• #1 Bow
•  #2 Bow
• #3 Bow
•  #4 Bow
• #5 Bow
• #6 Bow
• Front Window Retainer
• Lower Window Retainer
•  Rear Quarter Window

Two And Four Door Rear Components 

1. Rear Window Retainer Attachment Points
2. Quarter Window Pillars
3. Swing Gate Bar Retainers

NOTE:

• All lowering and raising the soft top instructions are applicable to both two and four-door model vehicles.
• Images shown are of four-door models, and the appearance of two-door model components may differ.
  • The following options are available to you when lowering your vehicle’s soft top:
• Sunrider® position with rear and quarter windows installed
• Sunrider® position with rear and quarter panels removed
• Sunrider® position with rear window installed and quarter panels removed
• Fully lowered position with rear and quarter windows removed
  Both quarter windows should be removed and installed together.

Lowering The Soft Top Into Sunrider® Position

1. Fold both sun visors forward against the windshield.
2. Release the header latches from the crossbar by pulling the handle downward. Make sure the hook is disengaged from its receiver.
3. From both the left and right sides, lift up on the #1 Bow of the soft top to start the operation.
4. Move to the side of the vehicle and use the side link to fold the soft top rearward into the Sunrider® position.
   
   NOTE:
   If leaving the soft top in the Sunrider® position, secure the top by using the two hook-and-loop fasteners provided in the center console.
   

NOTE:

• The vehicle can be driven in the Sunrider® position with the rear window and quarter panel assemblies fully installed or completely removed.
• The rear window and rear quarter windows must be removed before fully lowering the soft top to prevent damage to the top. Clean the side and rear windows before removal to assist in preventing scratching during removal of the soft top. If the plastic retainers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through an authorized dealer.

Removing The Soft Top Windows

NOTE:
Before fully lowering the soft top, the rear window and rear quarter windows must be removed.
Remove The Rear Window:

1. With the swing gate open, remove the rear window’s plastic retainers from the lower right and left corners.
2. Grab the swing gate bar, rotate it outward and upward releasing it from both the right and left retainers.
3. While holding the window in place, slide the swing gate bar to the left separating it from the rear window. Store in soft window bag (if equipped), or a safe location.
4. Remove the plastic retainers from both quarter window pillars.
5. While keeping the rear window level, slide to the left until it is completely separate from its retainer. Do not pull downward while removing the rear window. Damage to the retainer could result.

Remove The Right And Left Quarter Windows:

1. Through the rear opening, push the bottom corner outward and release tab from the bottom of the window pillar.
2. Undo the hook-and-loop fastener located at the upper front corner of each quarter window.
3. Starting at the rear of the vehicle, remove plastic retainer from along the bottom of the window moving toward the front of the vehicle.
4. Remove plastic retainer from the bottom to the top of the front window.
5. While keeping the window level, slide rearward until it is completely separate from its retainer. Do not pull downward while removing the window. Damage to the retainer could result.
6. Store in soft window bag (if equipped) or a safe location.

NOTE:
For information on the use of the storage bag, refer to the next section.

Soft Top Window Storage Bag — If Equipped
To safely store the soft top rear window, and rear quarter windows, proceed as follows:
NOTE:
The swing gate bar, once removed from the rear window, does not store in the soft window storage bag (if equipped).

1. With the bag opened completely, fold both fabric dividers downward and lay the first quarter window all the way to the right side with the inside of the window facing downward and the window pillar to the outside.
   NOTE:
   The quarter windows are marked “1” and “2” on the inside of the window pillar.
   1. Quarter Window Facing Downward
   2.  Both Dividers Folded Down
2. Fold the first divider upward, covering the first quarter window.
   
3. Lay the second quarter window on top of the first divider all the way to the left side with the inside of the window facing downward and the window pillar to the outside.
   
   1. Quarter Window Facing Downward
   2. Second Divider Folded Down
4. Fold the second divider upward, covering the second quarter window.
   
5. Lay the rear window on top of the second divider.
   
6. Close the storage bag and store in a safe location.
   

Lowering The Soft Top All The Way

1. Remove the rear window and quarter panel windows Ú page 82.
2. From the Sunrider® position Ú page 76, remove straps if previously secured and move to the rear of the vehicle.
3. Locate the Sunrider® latch beneath the #6 Bow of the soft top on the left side.
4. Pull the latch to release the top, and allow the soft top to slide rearward freely in the guide tracks to the stowed position.
   CAUTION! : Failure to follow the next steps could result in damage to the Soft Top or vehicle.
5. While pushing downward slightly on the folded soft top, slide the lock lever on the left and right side lift assist mechanisms to the “lock” position.
6. Once the lock lever is in the “lock” position, push downward on each side of the folded soft top to ensure it is secure. An audible “click” may be heard.
   NOTE: Secure the top by using the two hook-and-loop fasteners provided in the center console.

RAISING THE SOFT TOP

Use this QR code to access your digital experience.
Raising The Soft Top From The Fully Lowered Position

1. From the fully lowered position, remove straps if previously secured.
   CAUTION! Failure to follow the next steps could result in damage to the Soft Top or vehicle.
2. While pushing down on the rear of the top, slide the lock lever on the left and right side lift assist mechanisms to the “unlock” position.
3. Push up and forward from the #5 Bow along the guide track until it locks into the Sunrider® position with an audible “click”.
   1. Unlocked Position
   2.  #5 Bow Location
4. Gently pull rearward on the #6 Bow to ensure the top is locked in the Sunrider® position.
5. Using the side link, lift and push the soft top toward the front of the vehicle manually guiding the top into the closed position.
6. From inside the vehicle, pull the handle on the header latch downward to engage the hook into its receiver. Repeat on the other side.
7. Pull the handle back upward while squeezing the hook, locking the latch into place.

Installing The Soft Top Windows

Install The Right And Left Quarter Windows

1. From the rear of the vehicle, guide the top of the window into the retainer and slide forward while keeping the window level. Repeat on the other side.
2. Place the top of the quarter window pillar into the top cover, and insert the bottom tab into the clip.
   CAUTION! Failure to follow all Quarter Window Install steps could result in damage to the Soft Top or vehicle.
3. Engage the retainers on the front of the windows, ensuring they are fully engaged, followed by the retainers along the bottom of the windows.
   1. Retainer At Front Of Quarter Window
   2. Retainer At Bottom Of Quarter Window
      NOTE: It is critical that the retainers are fully engaged before the vehicle resumes motion.
4. Secure the hook-and-loop fastener at the upper front corner of each quarter window by pressing firmly.

Install The Rear Window

1. Guide the rear window into the retainer from left to right while keeping the window level.
2. Insert the swing gate bar into the retainers at the bottom of the window from left to the right.
3. Rotate the swing gate bar into the left and right side retainers.
4. Line up the rear window to the right side quarter window first, and engage the plastic retainers.
5. Repeat with the left side quarter window.
6. Engage the rear window retainers in the lower right and left corners.
   NOTE: For information on removing your soft top, refer to the next section.

REMOVING THE SOFT TOP

Use this QR code to access your digital experience.

1. Fully lower the soft top Ú page 85.
   CAUTION! Failure to follow the next steps could result in damage to the Soft Top or vehicle.
2. Make sure the lift assist mechanism on both the left and right sides are in the “lock” position, and an audible “click” is heard when pushing down on the #1 bow from each of the lift assist mechanisms before removing
3. Using the provided #40 Torx head driver and ratchet, unscrew the two Torx head screws on each lift assist mechanism, then lift the mechanism up and away from the vehicle.
   1. Lock Position
   2. Torx Head Screw
   3. Torx Head Screw
4. Pull the release lever on top of the rail rearward to release the side link from the track.
5. Repeat on the opposite side.
6. Utilizing two people, lift the soft top up and away from the vehicle, careful to avoid the vehicle’s sport bar, trim, and tire carrier. Store the soft top in a safe, clean, and dry location.
7. Using the provided #50 Torx head driver and ratchet, unscrew the Torx screw on both rear corners of the vehicle, removing the retainers.

INSTALLING THE SOFT TOP

1. If currently installed, remove the hard top Ú page 97.
2. Install the door rails, starting with the front, followed by the rear on each side. For instructions and appropriate torque specifications for the door rail Torx screws Ú page 107.
3. Install the rear retainers on each side of the rear of the vehicle using the provided #50 Torx head driver and ratchet. Refer to the following table for recommended torque specifications.
   CAUTION! Do not overtighten Torx screws. Damage to the retainers will occur.

   Torque Specification For Torx Screw	Maximum	Minimum
   119.5 in-lb	150.5 in-lb	106.2 in-lb
   13.5 N·m	17.0 N·m	12.0 N·m

   CAUTION! Failure to follow the next steps could result in damage to the Soft Top or vehicle.

4. Making sure the lift assist mechanism is in the “lock” position, lift the soft top into the rear of the vehicle with the side links pointing toward the front. Lower the lift assist mechanisms onto its retainers on both sides (on the inside of the sport bar).
5. Using the provided #40 Torx head driver and ratchet, tighten the Torx screws by turning them clockwise. Secure them until they are snug (refer to the following table for recommended torque specifications), being careful not to cross-thread the screws or overtighten. Repeat on the opposite side.
   1. Lock Position
   2.  Torx Head Screw
   3.  Torx Head Screw
      

      Torque Specification For Torx Screws	Maximum	Minimum
      119.5 in-lb	150.5 in-lb	106.2 in-lb
      13.5 N·m	17.0 N·m	12.0 N·m

      CAUTION! Do not overtighten the screws. You can strip the screws if they are overtightened.

6. While pulling the release lever on the top of the rail rearward, place the side link into the guide track on the top of the rail then release the lever.
7. Unsnap and remove the black boot cover. This cover should be discarded. It was intended as a protective cover for shipping only.
8. Raise the soft top Ú page 87.
9. NOTE: Be sure the wire harness in the left rear corner is not tangled in the soft top bows before you lift the top.

HARD TOP FRONT PANEL(S) REMOVAL

Use this QR code to access your digital experience.

CAUTION!

• The hard top is not designed to carry any additional loads, such as after-market roof racks, spare tires, building materials, hunting or camping supplies, etc. For optional Mopar® accessory roof racks Ú page 114.
• Do not move your vehicle until the top has been either fully attached to the front header, sport bar, and body side or fully removed.
  Failure to follow these cautions may cause interior water damage, stains or mildew:
• It is recommended that the top be free of water prior to panel removal. Removing the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle’s interior.
• The hard top assembly must be positioned properly to ensure sealing. Improper installation can cause water to leak into the vehicle’s interior.
• Careless handling and storage of the removable roof panels may damage the seals, causing water to leak into the vehicle’s interior.
• The front panel(s) must be positioned properly to ensure sealing. Improper installation can cause water to leak into the vehicle’s interior.

Four Door Hard Top Components

1. Right Side Panel
2.  Left Side Panel
3.  Hard Top

Two Door Hard Top Components

1. Right Side Panel
2.  Left Side Panel
3. Hard Top

NOTE:

• All hardtop removal and installation instructions are applicable to both two and four-door model vehicles.
• Images shown are of four-door models, and appearance of two-door model components may differ.
• The left side panel must be removed before removing the right-side panel.

To remove the hard top front panel(s), proceed as follows:

1. Fold-down the sun visor against the windshield.
2. Turn the three L-shaped locks on the left side panel (one at the front, the rear, and outside), unlocking them from the roof.
3. Unlatch the left side header panel latch located at the top of the windshield.
   1. Header Panel Latched
   2.  Unlatched Position
4. Remove the left side panel.
5. Repeat the previous steps to remove the right-side panel.

Hard Top Panel(s) Storage Bag — If Equipped
The Freedom Top panels storage bag allows you to store your hard top panels. The storage bag contains two compartments.
Lay the bag for the Freedom Top panels down so the loops and hooks are facing upward. Unzip the bag and fold back the outer flap.

NOTE:
Ensure the front panel latch is closed prior to inserting the panel into the panels bag.

1. Insert the left side hard top panel into the bag with the latches facing upward.
2. Unfold the black panel divider (ensure the divider is lying flat).
3. Insert the right side Freedom Top panel into the bag with the latches facing downward.
   NOTE: Ensure the front panel latch is closed prior to inserting the panel into the bag.
4. Unfold the outer flap and zip the hard top bag closed.
5. Lift the Freedom Top bag into the vehicle with the hooks and straps facing the back of the rear seat. Attach the clip at the bottom of the bag to the child restraint anchorage, located at the base of the rear seat.
6. Wrap the upper strap around the rear head restraints and loop the strap through the buckle. Pull on the strap to tighten the Freedom Top bag securely against the rear seat.

HARDTOP FRONT PANEL(S) INSTALLATION

1. Open the header latch inside the vehicle, and the three L-shaped locks on each panel.
2. Set the right-side panel on the windshield frame with the locating pin in the front receiver mounting hole followed by the left side panel, making sure there is no overhang. Also, make sure that the panels are sitting flush with the body.
3. Reinstall the panel(s) using the same steps for removal in reverse order.
   NOTE:
   To prevent water leaks, the seals and hard top panels should be clear of any dust and debris prior to reinstallation.

REMOVING THE HARD TOP

1. Remove both front panels Ú page 93.
2. Open both front doors.
3. Using the provided #50 Torx head driver and ratchet, remove the two Torx head screws that secure the hard top at the B-pillar (near the top of the front doors).
4. Remove the six Torx head screws that secure the hard top to the vehicle (along the interior bodyside — three screws on each side) using the #50 Torx head driver.
5. Open the swing gate all the way to ensure clearance of the rear window glass. Lift the rear window glass.
6. Locate the wire harness and washer hose on the left rear inside corner of the vehicle.
7. Release the locking tab by pushing it downward.
8. To remove the wiring harness, push the tab inward while pulling downward to disconnect.
9. To remove the washer hose, push the release button on hose connector, and pull downward.
10. Secure the wire harness to the body side by plugging it into the receptacle and reengaging the locking tab.
11. Secure the washer hose by snapping it into the top of the body side receptacle.
12. Lower the rear window, and close the swing gate.
13. Remove the hard top from the vehicle. Place the hard top on a soft surface to prevent damage.

CAUTION!
The removal of the rear Hard Top requires four adults, one located on each corner. Failure to follow this caution could damage the Hard Top.

INSTALLING THE HARD TOP]

If the door frames are installed from soft top usage, they must be removed prior to installation of the hard top. For removal procedures, see Ú page 106. To install the hard top, place the hard top on the vehicle while making sure that the top is sitting flush with the body at the sides and check to ensure that there is a uniform gap between the lift glass and hard top. Then follow the removal steps in reverse order.

NOTE:

• Inspect the hard top seals for damage and replace if necessary.
• The Torx fasteners that attach the hard top to the body should be torqued as follows using the provided #50 Torx head driver and ratchet:
  • Hard top to B-pillar: 119 in-lb +/- 23 in-lb (13.5 N·m +/- 2.7 N·m)
  • Hard top to J-rail: 154 in-lb +/- 30 in-lb (17.5 N·m +/- 3.5 N·m)

SUNRIDER® FOR HARD TOP

WARNING!
Do not open or close the Sunrider® top while driving. Operating the top while driving could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death.

The Sunrider® soft top can be used in place of the Hard Top Freedom Panels for quick and easy opening of the area above the driver and front passenger seats.

To install the Sunrider® soft top, proceed as follows:

1. Remove both front Hard Top Freedom panels Ú page 93.
2. With the help of a second person, set the Sunrider® top onto the top of the vehicle making sure to align the holes at the front and rear of the side rails.
3. Swing the front frame bracket around the side of the rail, and insert the door rail attachment bolt (provided bolt without spacer) from underneath. Tighten with a #40 Torx head driver until snug.
4. Insert the rear door rail attachment bolt (provided bolt with spacer) from underneath. Tighten with #40 Torx head driver until snug.
5. Repeat steps 3 and 4 on the other side of the vehicle.
   NOTE: The recommended torque specification for the front and rear door rail attachment bolts is 8.8 ft-lb (12 N·m).
6. Attach the rear clamp at the rear center of the Sunrider® top using the two provided rear clamp attachment bolts. Tighten with #40 Torx head driver until snug.
   NOTE:
   The recommended torque specification for the rear clamp attachment bolts is 3.7 ft-lb (5 N·m).
7. From inside the vehicle, lift and pull the Sunrider® top forward using the integrated handle on the front header of the top. Manually guide the top into the closed position.
8. From inside the vehicle, pull the handle on the header latch downward to engage the hook into its receiver. Pull the handle back upward while squeezing the hook, locking the latch into place. Repeat on the other side.

To Open The Sunrider® Top
To open the Sunrider® top, proceed as follows:

1. Fold both sun visors forward against the windshield.
2. Release the header latches from the crossbar by pulling the handle downward. Make sure the hook is disengaged from its receiver.
3. From the front of the Sunrider® top, lift and push the top rearward to the Sunrider® position.
4. Secure the top by using the two hook-and-loop fasteners provided with the Sunrider® kit, and wrap one around the side rails on each side of the Sunrider® top to hold it in place.

POWER SLIDING TOP — IF EQUIPPED

CAUTION!
Lowering of the windshield is NOT recommended in vehicles equipped with a Power Sliding Top. Damage will occur to the top as well as the header seal.

If your vehicle is equipped with a Power Sliding Top, the control switch can be found on the front trim panel, to the right of the driver’s side sun visor.

1. Open Switch
2.  Close Switch

NOTE:

• The power top is non-removable. If desired, the rear quarter windows can be removed and stored in the provided storage bag Ú page 104.
• The power top will not open in temperatures below -4°F (-20°C). However, if it is opened at a higher temperature, it can be closed at temperatures above -40°F (-40°C).
• The power top will not operate at vehicle speeds above 60 mph (96 km/h).

NOTE:
A slight pause in audio may be heard when opening and closing the Power Sliding Top as a result of the Uconnect system switching between power top Closed and power top Open audio modes.

WARNING!

• Never leave children unattended in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle, or in a location accessible to children. Do not leave the Keyless Enter ‘n Go™ Ignition in the ACC or ON/RUN position. Occupants, particularly unattended children, can become entrapped by the power top while operating the power top switch. Such entrapment may result in serious injury or death.
• In a collision, there is a greater risk of being thrown from a vehicle with an open power top. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are also properly secured.
• Do not allow small children to operate the power top. Never allow your fingers, other body parts, or any object, to project through the power top opening. Injury may result.

Opening And Closing The Power Top

Express Open/Close
Push the open switch and release it within one-half second and the power top will open automatically from any position. The power top will open fully and stop automatically.
Push the close switch and release it within one-half second and the power top will close automatically from any position. The power top will close fully and stop automatically.
During Express Open or Express Close operation, any other movement of the power top switch will stop the power top.
Manual Open/Close
To open the power top manually, push and hold the open switch to the full open position, then release. To close the power top manually, push and hold the close switch to the fully closed position, then release.
Any release of the switch during open or close operation will stop the power top movement. The top will remain in a partially opened position until the switch is operated and held again.
Pinch Protect Feature
This feature will detect an obstruction in the opening of the power top during Express Close operation. If an obstruction in the path of the power top is detected, the power top will automatically retract. Remove the obstruction if this occurs. Next, push the close switch and release to Express Close.

WARNING!
There is no anti-pinch protection when the power top is almost closed. To avoid personal injury be sure to clear your arms, hands, fingers and all objects from the top’s path before closing.

NOTE:

• The Power Sliding Top may reverse motion if closing during a severe headwind. If this occurs, push and hold the Power Sliding Top switch again to close the top completely.
• If three consecutive power top close attempts result in Pinch Protect reversals, Pinch Protect will disable and the power top must be closed in Manual Mode.

Power Top Maintenance
Use only a non-abrasive cleaner and a soft cloth to clean the quarter window glass panel. For important information on cleaning and caring for your vehicle Ú page 408.
Ignition Off Operation
The power top switch can remain active in Accessory Delay for up to approximately 10 minutes after the vehicle’s ignition is placed to the OFF position. Opening either front door will cancel this feature.
NOTE:
Ignition Off time is programmable through the Uconnect system Ú page 207.

Relearn Procedure
For vehicles equipped with a power top, there is a relearn procedure that allows you to calibrate the power top when the “Express Mode” stops working. To reset the power top, follow these steps:

1. Place the ignition in the RUN position, and start the vehicle.
   NOTE: The engine must be running to perform the relearn procedure.
2. Ensure the power top is in the fully closed position.
3. Push and hold the Close switch for 10 seconds. This will put the power top into calibration mode.
4. Continue holding down the close button while the top goes fully open and then back to fully close.
5. Once the power top has stopped in the fully closed position, release the close button. The power top is now reset and ready to use.
   NOTE: If the close button is released anytime during the relearning process, the relearn may not be complete, and the procedure must be repeated.

Rear Quarter Window Removal
On vehicles equipped with a Power Sliding Top, the rear quarter windows can be removed. To remove these windows, follow this procedure:

1. Open the swing gate, and lift the rear window.
2. Open both side doors nearest the quarter windows.
3. Locate the rear quarter window latches (two on each window) on the interior of the windows.
4. Rotate the left-hand side latch clockwise to release.
5. Rotate the right-hand side latch counterclockwise to release.
   1. Rotate Left Handle Clockwise
   2. Rotate Right Handle Counterclockwise
6. From the outside of the vehicle, lift each window upward and away from the vehicle.
   NOTE: Do not pull down or apply any weight to the windows after the latches are released. Damage could result to the pins holding the windows in place.
7. Store the rear quarter windows in the provided storage bag and keep in a safe location, or securely fasten the bag to the rear seat.

Quarter Window Storage Bag
To use the storage bags for the rear quarter windows, proceed as follows:

1. With the bag completely open and the fabric divider raised, place the first quarter window with the latches facing outward into the foam insert. Fold divider over the window once placed inside.
   1. Bag Open With Divider Raised
   2. Lower Divider Over Window (Latches Facing Outward)
2. Place the second window into the foam insert with the latches facing outward. Fully close the bag.
   NOTE: Once both windows are placed inside the bag, the outside of the windows will be facing each other with all latches facing the outside of the bag.
   
   1. Second Window Placed Over Divider
   2. Fully Closed Bag
3. Store the bag in a safe location, or in the cargo area of the vehicle by securing the bag in the vehicle’s cargo area. This is done by attaching the straps at the top of the bag to the rear head restraints, as well as attaching the clip at the bottom of the bag to the forward most cargo hook on the load floor.