The washer nozzles are heated (Option/accessory) automatically in cold weather to prevent the washer fluid from freezing.
Information indicating that the washer fluid needs topping up appears in the driver display when there is approx. 1 liter (1 qt) of washer fluid remaining.
Setting the wiper blades in service position
Wiper blades in service position.
In order to change, clean or lift the wiper blades (e.g. for scraping off ice from the windscreen) they must be in service position.
Important: Before placing the wiper blades in the service position, make sure that they are not frozen down.
Activating/deactivating service modeService mode can be activated/deactivated when the car is stationary and the windscreen wipers are not on. Service mode is activated/deactivated via the centre display:
Press
Then tap on Controls and activate/deactivate wiper blade service position.
The wiper blades also exit the service position if:
- Windscreen wiping is activated.
- Windscreen washing is activated.
- The rain sensor is activated.
- The car is driven away.
Important: If the wiper arms in service position have been folded up from the windscreen, they must be folded back down onto the windscreen before the activation of wiping, washing or the rain sensor, as well as before driving. This is to avoid scraping the paint on the bonnet.
Setting the wiper blades in service position
Wiper blades in service position.
In order to change, clean or lift the wiper blades (e.g. for scraping off ice from the windscreen) they must be in service position.
Important: Before placing the wiper blades in the service position, make sure that they are not frozen down.
Activating/deactivating service modeService mode can be activated/deactivated when the car is stationary and the windscreen wipers are not on. Service mode is activated/deactivated via the centre display:
Press
Then tap on Controls and activate/deactivate wiper blade service position.The wiper blades also exit the service position if:
- Windscreen wiping is activated.
- Windscreen washing is activated.
- The rain sensor is activated.
- The car is driven away.
Important: If the wiper arms in service position have been folded up from the windscreen, they must be folded back down onto the windscreen before the activation of wiping, washing or the rain sensor, as well as before driving. This is to avoid scraping the paint on the bonnet.
Topping up washer fluid
Note: When approx. 1 litre (1 qt) of washer fluid remains in the reservoir, the message Refill washer fluid, level low appears together with the
When the Refill washer fluid, level low message together with the
Open the bonnet with the handle in the passenger compartment and then with the handle under the front edge of the bonnet.
Open the washer fluid reservoir cap.
Washer fluid is filled into the reservoir with the blue cap. The reservoir is used for windscreen washer, rear window washer and headlamp washers.(Option/accessory)
Top up with washer fluid.
Close the washer fluid reservoir cap and then close the bonnet.
Prescribed grade: Washer fluid recommended by Volvo – with frost protection during cold weather and for temperatures below freezing point.
Important:Use Volvo genuine washer fluid or equivalent with a recommended pH of between 6 and 8, in working dilution (e.g. 1:1 with neutral water).
Important:Use washer fluid with antifreeze when the temperature is below freezing to avoid the fluid freezing inside the pump, reservoir and hoses.
Volume:
- Cars with headlamp washing: 5.5 litres (5.8 qts).
- Cars without headlamp washing: 3.5 litres (3.7 qts).
Replacing the wiper blade, rear window
Replacing the wiper blade, rear window
Lift the wiper arm from the window and pull the lower section of the blade to the right.
- Grip the centre of the wiper arm and lift it from the windscreen to lock position.
Note:There is a lock position at a half extension angle that may feel like resistance. This lock prevents the arm from falling back against the windscreen. The wiper arm must be pulled past the lock for wiper blade replacement.
- Grip the lower part of the blade and pull to the right until the blade loosens from the arm.
Press the new wiper blade into place. You should be able to hear a click. Check that it is firmly installed.
Lower the wiper arm.
Important:Check the blades regularly. Neglected maintenance shortens the service life of the wiper blades.
Replacing windscreen wiper blades
- Fold up the wiper arm when it is in service position. Service position is activated/deactivated via the centre display when the car is stationary and the windscreen wipers are not switched on. Press the button located on the wiper blade mounting and pull straight out parallel with the wiper arm.
- Slide in the new wiper blade until a “click” is heard.
Check that the blade is firmly installed.
Fold the wiper arm back towards the windscreen.
The wiper blades are different lengths
Note:When replacing the wiper blades, note that they have different lengths. The blade on the driver’s side is longer than on the passenger side.