Designation of dimensionsAll tyres have a dimension designation, such as 235/60 R18 103 H.
| 235 | Tyre width (mm) |
| 60 | Ratio between tyre wall height and tyre width (%) |
| R | Radial ply |
| Rim diameter in inches | |
| 103 | Codes for the maximum permitted tyre load, tyre load index (LI) |
| H | Speed rating for maximum permitted speed, speed rating (SS). (In this case 210 km/h (130 mph).) |
Load index
Each tyre has a certain capacity to carry a load, a load index (LI). The car’s weight determines the load capacity required of the tyres.
Each tyre has a certain capacity to carry a load, a load index (LI). The car’s weight determines the load capacity required of the tyres.
Speed rating
Each tyre can withstand a certain maximum speed. Tyre speed rating, SS (Speed Symbol), must at least correspond with the car’s top speed. The table below shows the maximum permitted speed for each speed rating (SS). The only exception to these regulations is winter tyres, where a lower speed rating may be used. If such a tyre is selected, the car must not be driven more quickly than the tyre is rated for. For example, cars with Q rating tyres must be driven at speeds not exceeding 160 km/h (100 mph). The road conditions and applicable road traffic rules determine how quickly the car can be driven, not the speed rating of the tyres.
Each tyre can withstand a certain maximum speed. Tyre speed rating, SS (Speed Symbol), must at least correspond with the car’s top speed. The table below shows the maximum permitted speed for each speed rating (SS). The only exception to these regulations is winter tyres, where a lower speed rating may be used. If such a tyre is selected, the car must not be driven more quickly than the tyre is rated for. For example, cars with Q rating tyres must be driven at speeds not exceeding 160 km/h (100 mph). The road conditions and applicable road traffic rules determine how quickly the car can be driven, not the speed rating of the tyres.
Note
The maximum permitted speed is specified in the table.
The maximum permitted speed is specified in the table.
| Q | 160 km/h (100 mph) (used only on winter tyres) |
| T | 190 km/h (118 mph) |
| H | 210 km/h (130 mph) |
| V | 240 km/h (149 mph) |
| W | 270 km/h (168 mph) |
| Y | 300 km/h (186 mph) |
Warning
The lowest permitted load index (LI) and speed rating (SS) for the tyres for each respective engine variant are shown by the specifications. If a tyre with too low a load index or speed rating is used, it may overheat and be damaged.
The lowest permitted load index (LI) and speed rating (SS) for the tyres for each respective engine variant are shown by the specifications. If a tyre with too low a load index or speed rating is used, it may overheat and be damaged.
Approved tyre pressures
Approved tyre pressures for each engine alternative can be found in the table.
Note
All engines, tyres or combinations of these are not always available in all markets.
| Engine | Tyre dimension | Speed | Load, 1-3 persons | Max. load | ECO pressure | ||
|---|---|---|---|---|---|---|---|
| Front kPa (psi) | Rear kPa (psi) | Front kPa (psi) | Rear kPa (psi) | Front/rear kPa (psi) | |||
| All engines | 235/55 R19 275/45 R20 275/40 R21 275/35 R22 | 0-180 km/h (0-112 mph) | 260 (38) | 260 (38) | |||
Tyres’ rotation direction
Tyres with a tread pattern which are designed to only turn in one direction have the direction of rotation marked with an arrow.
The arrow shows the tyre’s direction of rotation.
- Tyres must rotate in the same direction during their entire service life.
- Tyres should only be switched between front and rear positions, never between left and right-hand sides, or vice versa.
- If the tyres are fitted incorrectly, the car’s braking characteristics and capacity to force rain and slush out of the way are adversely affected.
- The tyres with the deepest tread depth should always be fitted to the rear of the car in order to reduce the risk of oversteer skidding.
- On cars with different front and rear tyre or wheel dimensions, it is not permitted to change position between front and rear wheels.
- Volvo recommends that the rear tyres do not have substantially less tread depth than the front tyres in order to reduce the risk of oversteer skidding when driving on wet roads.
Note
Make sure that the front and rear axles have the same type, dimension and make of tyres.Cars with different front and rear tyre dimensions must have the same type and make of tyres on the front and rear axles.
Make sure that the front and rear axles have the same type, dimension and make of tyres.Cars with different front and rear tyre dimensions must have the same type and make of tyres on the front and rear axles.
Tread wear indicators on the tyres
Tread wear indicators show the status of the tyre’s tread depth.
A tread wear indicator is a narrow elevation across the longitudinal grooves of the tyre’s tread pattern. On the side of the tyre are the letters TWI (Tread Wear Indicator). When the tyre’s tread depth is down to 1.6 mm (1/16 inch), the tread will be level in height with the tread wear indicators. Change to new tyres as soon as possible. Remember that tyres with little tread depth provide very poor grip in rain and snow.
Dimension designation for wheel rim
Wheel and rim dimensions are designated in accordance with the examples in the table below.The car has an approval for the complete vehicle with certain combinations of wheel rims and tyres.
All wheel rims have a dimension designation, for example: 8Jx18x42.5.
| 8 | Rim width in inches |
| J | Rim flange profile |
| 18 | Rim diameter in inches |
| 42.5 | Off-set in mm (distance from wheel centre to wheel contact surface against the hub) |
Minimum permitted tyre load index and speed rating for tyres
The table below shows minimum permitted load index (LI) and speed rating (SS) for tyres.
| Engine | Minimum permitted load index (LI) | Minimum permitted speed rating (SS) |
|---|---|---|
| All engines | 104 | H |