Note
It is recommended that brake fluid is changed or filled by an authorized Volvo workshop.
It is recommended that brake fluid is changed or filled by an authorized Volvo workshop.
Brake functions
The car’s brakes are used to reduce the speed or prevent the car from rolling. Besides the foot brake and parking brake, the car is equipped with several automatic brake assist functions. These can assist the driver by not needing to keep his/her foot on the brake pedal when at a traffic light, or when starting on an uphill gradient. Depending on the car’s equipment, the following auto braking functions are available:
- Automatic brake when stationary (Auto hold)
- Hill start assist (Hill Start Assist)
- Auto braking after a collision
- Regenerative braking
- Warning and auto-brake when reversing
- Assistance at risk of collision
- Off-road mode
- Hill descent control (Hill Descent Control)(Option/accessory)
Automatic braking when stationary
Automatic brake when stationary (Auto hold) means that the driver can release the brake pedal while maintaining a braking effect when the car has stopped at traffic lights or a junction.
When the car has stopped, the brakes are activated automatically. The function can use either a foot brake or parking brake to hold the car stationary and it works on all gradients. When driving off, the brakes are released automatically if the driver is wearing the seatbelt and/or the driver’s door is closed.
Note
When braking to a standstill on an uphill or downhill slope, the brake pedal should be depressed a little harder before being released to ensure the car does not roll. The parking brake is activated automatically
When braking to a standstill on an uphill or downhill slope, the brake pedal should be depressed a little harder before being released to ensure the car does not roll. The parking brake is activated automatically
- if the car is switched off
- when the driver unbuckles the seatbelt and/or opens the driver’s door.
- if the function Auto hold (brake when stationary) is activated and the car has been stationary for a while (approx. 5–10 minutes).
Auto hold can also change over to the parking brake in other situations.
Symbols in the driver display
| Symbol | Specification |
|---|---|
| | The symbol is illuminated when the function uses the foot brake to keep the car stationary. Note that the foot brake may be active even if the symbol is not lit. |
| | The symbol is illuminated when the function uses the parking brake to keep the car stationary. |
Activating and deactivating the automatic brake at a standstill
The automatic brake function at a standstill is activated using the button in the tunnel console.
Applicable when switching off
If the function is active and holds the car with the foot brake (A-symbol illuminated in the driver display), the brake pedal must be depressed at the same time as the button is depressed in order to deactivate.
- The function remains deactivated until it is reactivated.
- When the function is deactivated, brake assist remains active to prevent the car from rolling backward when starting on an uphill gradient.
Auto braking after a collision
In the event of a collision in which the activation level is reached for the pyrotechnic seatbelt tensioners or airbags, or if a collision with a large animal is detected, the car’s brakes are automatically applied. This function is to prevent or reduce the effects of any subsequent collision. After a serious collision, there is a risk that it is no longer possible to control and steer the car. In order to avoid or mitigate a possible further collision with a vehicle or an object in the vehicle’s path, the auto braking system is activated automatically and brakes the car in a safe manner. Brake lights and hazard warning lights are activated during braking. When the car has stopped, the hazard warning lights continue to flash and the parking brake is applied. If braking is not appropriate, e.g. if there is a risk of being hit by following traffic, the system can be overridden by the driver depressing the accelerator pedal. The function assumes that the brake system is intact after the collision.
Regenerative braking
(Option/accessory)
The car recovers kinetic energy during braking in order to reduce fuel consumption and emissions. The function is available in all drive modes together with gear position D or M.
Activating brake regeneration
- Depress the brake pedal.
The car brakes and regenerates energy.
Regeneration increases during engine braking when manual gearshift mode M is selected.
Symbols in the driver display
If the car is a mild hybrid, a battery symbol is shown on the right-hand side of the driver display.
When the battery is being charged, such as during regenerative braking, it is indicated by this symbol.