Warning
- If a wheel must be changed in a trafficked environment, passengers must stand in a safe place.
- Use a jack designed for the car when changing tires. Use supports to secure the car for all other work.
- Never crawl under the car or reach under with a part of your body when it is raised on a jack.
- Passengers must leave the car when it is raised on the jack.
Important
- The jack included with the car is only designed for occasional, short-term use, such as when changing a wheel after a puncture. Only the jack belonging to the specific model is to be used to jack up the car. If
- the car is to be jacked up more often, or for a longer time than is required just to change a wheel, the use of a garage jack is recommended. In this instance, follow the instructions for use that come with the
- equipment. When the jack is not in use it must be stored in its storage space under the cargo area floor. The jack needs to be cranked together to the correct position in order to have space.
Removing a wheel
- Read through all instructions before beginning. Take out the tools needed before jacking up the car.
- Activate the hazard warning flashers and set out a warning triangle if a wheel shall be changed in a trafficked location.
- Make sure that the parking brake is activated and engage gear position P.
- Chock in front of and behind the wheels that remain on the ground. Use, for example, heavy wooden blocks or large stones.
- Screw together the towing eye with the wheel wrench to the stop position.
- With the car still on the ground, use the wheel bolt wrench/towing eye to undo the wheel bolts ½-1 turn by pressing downwards (anticlockwise). Always start with the lockable wheel bolts.
- Follow the instructions on how to safely raise the car with the jack.
- Raise the car high enough to allow the wheel to be removed to move freely. Remove the wheel bolts and lift off the wheel.
Mounting a wheel
- Clean the surfaces between wheel and hub.
- Put on the wheel. Ensure that the correct dimension is fitted in the correct position for cars with different front and rear tire or wheel dimensions. Tighten the wheel bolts thoroughly.
- Do not use lubricant on the threads of the wheel bolts.
- Lower the car so that the wheels cannot rotate.
- Tighten the wheel bolts crosswise. It is important that the wheel bolts are tightened properly. Tighten to 140 Nm (103 foot-pounds). Check the tightening torque with a torque wrench.
- Check the tire pressure and save the new tire pressure in the system for tire pressure monitoring.
Warning
The wheel bolts may need to be re-tightened several days after the wheel change. Temperature differences and vibration may mean that they are not attached equally as tightly.
The wheel bolts may need to be re-tightened several days after the wheel change. Temperature differences and vibration may mean that they are not attached equally as tightly.
Note
- After a tire has been inflated, always refit the dust cap in order to avoid damage to the valve from gravel, dirt, etc.
- Only use plastic dust caps. Metal dust caps can rust and become difficult to unscrew.
Jack
The jack can be used to raise the car, for example, to change a wheel.
The jack included with the car is only designed for occasional, short-term use, such as when changing a wheel after a puncture. Only the jack belonging to the specific model is to be used to jack up the car. If the car is to be jacked up more often, or for a longer time than is required just to change a wheel, the use of a garage jack is recommended. In this instance, follow the instructions for use that come with the equipment. When the jack is not in use it must be stored in its storage space under the cargo area floor. The jack needs to be cranked together to the correct position in order to have space.
Wheel bolts
Wheel bolts are used to attach the wheels to the hubs.
Only use rims that are tested and approved by Volvo and which are Volvo genuine accessories.
Check the tightening torque of the wheel bolts with a torque wrench.
Do not use lubricant on the threads of the wheel bolts.
Only use rims that are tested and approved by Volvo and which are Volvo genuine accessories.
Check the tightening torque of the wheel bolts with a torque wrench.
Do not use lubricant on the threads of the wheel bolts.
Warning
The wheel bolts may need to be re-tightened several days after the wheel change. Temperature differences and vibration may mean that they are not attached equally as tightly.
The wheel bolts may need to be re-tightened several days after the wheel change. Temperature differences and vibration may mean that they are not attached equally as tightly.
Important
The wheel bolts must be tightened to 140 Nm. (103 foot-pounds). Overtightening or loose tightening may damage the nuts and the bolts.
The wheel bolts must be tightened to 140 Nm. (103 foot-pounds). Overtightening or loose tightening may damage the nuts and the bolts.
Lockable wheel bolt kit
To loosen or tighten the lockable wheel bolts – turn the wrench in the lock bolt until it fully engages in the code grooves. Always start with the lockable wheel bolts if the wheel shall be removed. When fitting the wheel, finish with the lock screw.
Important
Remember not to use bending force when you loosen/tighten the wheel bolts. This could damage the code groove in the lock bolt and the wheel wrench and so make it impossible to fit/remove the wheel.
When the wheel wrench is not in use it must be stored in its place in the foam block under the cargo area floor. It is important to remember this if the car is due to visit a workshop in order to have the tool available. If you lose the wrench, contact your Volvo dealer.
Remember not to use bending force when you loosen/tighten the wheel bolts. This could damage the code groove in the lock bolt and the wheel wrench and so make it impossible to fit/remove the wheel.
When the wheel wrench is not in use it must be stored in its place in the foam block under the cargo area floor. It is important to remember this if the car is due to visit a workshop in order to have the tool available. If you lose the wrench, contact your Volvo dealer.
Spare wheel
- The spare wheel, the Temporary Spare type, can be used to temporarily replace a punctured normal wheel.
- The spare wheel is only designed for temporary use. Replace it with a normal wheel as soon as possible.
- The car’s driving characteristics can be changed when the spare wheel is used and the ground clearance is reduced. Do not wash the car in an automatic car wash if the Temporary Spare is being used.
- Recommended tire pressure must be maintained regardless of the position of the temporary spare wheel on the car.
- If the spare wheel is damaged, a new one can be purchased from a Volvo dealer.
Warning
- Never drive faster than 80 km/h (50 mph) with a spare wheel fitted on the car.
- The car must never be driven fitted with more than one “Temporary Spare” wheel.
- The car may have different driving characteristics while driving with the spare wheel. The spare wheel must be replaced with a normal wheel as soon as possible.
- The spare wheel is smaller than the normal wheel, which affects the car’s ground clearance. Look out for high curbs and do not machine-wash the car.
- Follow the manufacturer’s recommended tire pressure for the spare wheel.
- On all-wheel drive cars, the drive on the rear axle can be disengaged.
- If the spare wheel is fitted to the front axle then it is not possible to use snow chains at the same time.
- The spare wheel must not be repaired.
ImportantThe car must not be driven with tires of different dimensions or with a spare tire other than the one the car is approved for. Using tires of different dimensions can cause serious damage to the car’s transmission due to the different rolling circumferences. Cars designed for different front and rear tire or wheel dimensions must have the same type and make of tires on the front and rear axles.
Handling the spare wheel
Follow these instructions for handling the spare wheel.
Taking out the spare wheel
- The illustration is generic and its appearance may differ.
- The spare wheel is located under the load floor and is attached by a strap. The foam block contains all the tools for changing a wheel.
- Fold up the cargo area floor.
- Undo the straps and lift out the spare wheel.
Storing the punctured tire
Put the tools back in their right place in the foam block.
Then fold down the cargo area floor and place the punctured tire in the cargo area.
Snow chains
The use of snow chains and/or winter tires can help to improve the traction in winter conditions.
Volvo recommends that snow chains are not used on wheel dimensions greater than 18 inches.
Volvo recommends that snow chains are not used on wheel dimensions greater than 18 inches.
Warning
Use Volvo genuine snow chains or equivalent chains designed for the car model, and tire and rim dimensions. Only single-sided snow chains are permitted.
In the event of uncertainty about the show chain, Volvo recommends that an authorized Volvo workshop should be contacted. The wrong snow chains may cause serious damage to the car and lead to an accident.
Using snow chains may result in a malfunction of the tire pressure monitoring system.
Use Volvo genuine snow chains or equivalent chains designed for the car model, and tire and rim dimensions. Only single-sided snow chains are permitted.
In the event of uncertainty about the show chain, Volvo recommends that an authorized Volvo workshop should be contacted. The wrong snow chains may cause serious damage to the car and lead to an accident.
Using snow chains may result in a malfunction of the tire pressure monitoring system.
Important
Snow chains can be used on the car with the following restrictions:
Snow chains can be used on the car with the following restrictions:
- Always follow the mounting instructions from the manufacturer carefully. Fit the chains as tension as possible and tension them at regular intervals.
- Snow chains must only be used on the front wheels (also applies to all-wheel drive cars).
- In some cases, snow chains must NOT be used, such as if accessory, aftermarket, or “special” tires, and wheels are fitted that has a different size to the original tires and wheels. Sufficient distance must be maintained between the chains and brakes, suspension, and body components.
- Check local regulations with regard to using snow chains before fitting them.
- Never exceed the chain manufacturer’s specified maximum speed. You must never exceed 50 km/h (30 mph) under any circumstances.
- Avoid bumps, holes, or sharp turns when driving with snow chains.
- Avoid driving on bare ground as this wears out both the snow chains and tires.
- Driving with snow chains may have a negative effect on the car’s driving characteristics. Avoid fast or sharp turns, as well as braking with locked wheels.
- Some types of chains that are firmly tensioned affect brake components and must therefore NOT be used.
- You can obtain more information on snow chains from a Volvo dealer.
Winter tires
Winter tires are adapted for winter road conditions.
Volvo recommends winter tires specially developed for winter driving on all wheels if there is a risk of snow or ice. Tire dimensions are dependent on engine variants. When driving on winter tires, the correct type of tires must be fitted to all four wheels.
Tips for changing to winter tires
When summer and winter wheels are changed, mark which side of the car they were mounted on, for example, L for left and R for right.
Contact a Volvo dealer for advice about which wheel rim and tire types are most suitable.
Studded tires
Studded winter tires should be run in gently for 500-1000 km (300-600 miles), so the studs settle properly into the tires. This gives the tire, and especially the studs, a longer service life.
Note
Laws regarding the use of studded tires may vary. Always follow local laws and regulations.
Tread depth
Road conditions with ice, slush, and low temperatures place considerably higher demands on tires than summer conditions. Volvo, therefore, recommends not to drive on winter tires that have a tread depth of less than 4 mm (0.15 inches).
Punctures
Activate the hazard warning flashers if the car has a puncture in a trafficked environment.
Think about safety. If possible, move the car out of danger from traffic. Call roadside assistance if necessary.
If possible, exit the car from the side with the least traffic.
Put on a reflective vest and then position the warning triangle so that other road users are warned in good time.
Think about safety. If possible, move the car out of danger from traffic. Call roadside assistance if necessary.
If possible, exit the car from the side with the least traffic.
Put on a reflective vest and then position the warning triangle so that other road users are warned in good time.
Dealing with a puncture
The car is equipped with either a puncture repair kit for temporary tire repair or a spare wheel, see the respective section for user instructions.
Tool kit
Tools that can be useful during towing, wheel changes, or similar are found in the car’s cargo area.
- Jack
- Tool for removing the plastic caps from the wheel bolts
- Funnel for filling fluids
- Wheel wrench and towing eye
- If the car is fitted with a spare wheel, there is a jack and a wheel bolt wrench instead of an emergency puncture repair kit.