Wiper blades in the service position. In order to change, clean or lift the wiper blades (e.g. for scraping off ice from the windscreen) they must be in service position.
Important
Before placing the wiper blades in the service position, make sure that they are not frozen down.
Before placing the wiper blades in the service position, make sure that they are not frozen down.
Activating/deactivating service mode
Service Mode can be activated/deactivated when the car is stationary and the windscreen wipers are not on. Service mode is activated/deactivated via the center display:
- Press in the centre display.
- Then tap on Controls and activate/deactivate wiper blade service position.
The wiper blades also exit the service position if:
- Windscreen wiping is activated.
- Windscreen washing is activated.
- The rain sensor is activated.
- The car is driven away.
Important
If the wiper arms in service position have been folded up from the windscreen, they must be folded back down onto the windscreen before the activation of wiping, washing or the rain sensor, as well as before driving. This is to avoid scraping the paint on the bonnet.
If the wiper arms in service position have been folded up from the windscreen, they must be folded back down onto the windscreen before the activation of wiping, washing or the rain sensor, as well as before driving. This is to avoid scraping the paint on the bonnet.
Topping up washer fluid
Washer fluid is used for cleaning the headlamps as well as the windscreen and rear window. Washer fluid with antifreeze must be used when the temperature is under the freezing point.
Note
When approx. 1 litre (1 qt) of washer fluid remains in the reservoir, the message Refill washer fluid, level low appears together with the symbol in the driver display.
When approx. 1 litre (1 qt) of washer fluid remains in the reservoir, the message Refill washer fluid, level low appears together with the symbol in the driver display.
When the Refill washer fluid, level low message together with the symbol appear in the driver display, it is time to refill washer fluid
- Open the bonnet with the handle in the passenger compartment and then with the handle under the front edge of the bonnet.
- Open the washer fluid reservoir cap.
- Washer fluid is filled into the reservoir with the blue cap. The reservoir is used for windscreen washer, rear window washer and headlamp washers. (Option/accessory)
- Top up with washer fluid.
- Close the washer fluid reservoir cap and then close the bonnet.
Prescribed grade: Washer fluid recommended by Volvo – with frost protection during cold weather and for temperatures below freezing point.
Important
Use Volvo genuine washer fluid or equivalent with a recommended pH of between 6 and 8, in working dilution (e.g. 1:1 with neutral water). Use washer fluid with antifreeze when the temperature is below freezing to avoid the fluid freezing inside the pump, reservoir and hoses.
Use Volvo genuine washer fluid or equivalent with a recommended pH of between 6 and 8, in working dilution (e.g. 1:1 with neutral water). Use washer fluid with antifreeze when the temperature is below freezing to avoid the fluid freezing inside the pump, reservoir and hoses.
Volume:
- Cars with headlamp washing: 5.5 litres (5.8 qts).
- Cars without headlamp washing: 3.5 litres (3.7 qts).
Replacing the wiper blade, rear window
The wiper blades sweep water away from the windscreen and rear window. Together with washer fluid, they aim to clean the windows and ensure visibility while driving. Windscreen and rear window wiper blades can be replaced.
Replacing the wiper blade, rear window
Lift the wiper arm from the window and pull the lower section of the blade to the right.
- Grip the center of the wiper arm and lift it from the windscreen to lock position.
Note
There is a lock position at half extension angle that may feel like resistance. This lock prevents the arm from falling back against the windscreen. The wiper arm must be pulled past the lock for wiper blade replacement. - Grip the lower part of the blade and pull to the right until the blade loosens from the arm.
- Press the new wiper blade into place. You should be able to hear a click. Check that it is firmly installed.
- Lower the wiper arm.
Important
Check the blades regularly. Neglected maintenance shortens the service life of the wiper blades.
Check the blades regularly. Neglected maintenance shortens the service life of the wiper blades.
Replacing windscreen wiper blades
The wiper blades sweep the water away from the windscreen and rear window. Together with washer fluid, they aim to clean the windows and ensure visibility while driving. The windscreen and rear window wiper blades can be replaced.
- Fold up the wiper arm when it is in the service position. Service position is activated/deactivated via the centre display when the car is stationary and the windscreen wipers are not switched on. Press the button located on the wiper blade mounting and pull straight out parallel with the wiper arm.
- Slide in the new wiper blade until a “click” is heard.
- Check that the blade is firmly installed.
- Fold the wiper arm back towards the windscreen.
The wiper blades are different lengths
Note
When replacing the wiper blades, note that they have different lengths. The blade on the driver’s side is longer than on the passenger side.
When replacing the wiper blades, note that they have different lengths. The blade on the driver’s side is longer than on the passenger side.