Short flash sequence
| Move the stalk switch up or down to the first position and release. The direction indicator lamps flash three times. |
This automatic flashing sequence can be stopped by moving the stalk switch immediately in the opposite direction.
Continuous flash sequence
| Move the stalk switch up or down to its end position. |
The stalk switch remains in its position and is moved back manually, or automatically by the steering wheel movement.
If the symbol for direction indicators in the driver display flashes more quickly than normal – see the message in the driver display.
Brake lights
- The brake light automatically comes on during braking.
- The brake light is illuminated when the brake pedal is depressed and when the car is braked automatically by one of the driver support systems.
Rear fog lamp
The rear fog lamp is considerably stronger than the normal rear lights and should only be used in reduced visibility due to fog, snow, smoke or dust so that other road users have an early warning of a vehicle ahead.
Button for rear fog lamp.
- The rear fog lamp is a lamp at the rear of the car, on the driver’s side.
- The rear fog lamp can only be switched on when ignition position II is active and the rotating ring on the stalk switch is in position AUTO or
- Press the button to switch the lights on/off. The
- The rear fog lamp switches off automatically when the car is switched off or when the rotating ring on the stalk switch is set to the 0 or
Regulations on the use of rear fog lamps vary from country to country.
Dipped beam
When driving with the stalk switch’s rotating ring in the AUTO position, dipped beam is activated automatically in weak daylight or darkness or when the car’s electrical system is in ignition position II.
talk switch rotating ring in AUTO position.
With the stalk switch’s rotating ring in AUTO position, the dipped beam is also activated automatically if the rear fog lamp is activated.
With the stalk switch’s rotating ring in the position, the dipped beam is always activated when the car’s electrical system is in ignition position II.
Tunnel detection
- The car detects when it is driven into a tunnel and switches from daytime running lights to dipped beams.
- Note that the rotating ring in the left-hand stalk switch must be in AUTO mode for tunnel detection to work.
Using main beam
Main beam is operated with the left-hand stalk switch. Main beam is the car’s strongest lighting and should be used when driving in the dark for better visibility, as long as it does not dazzle other road users.
Steering wheel stalk switch with rotating ring.
Main beam flash
| Move the stalk switch backwards slightly to main beam flash position. Main beam comes on until the stalk switch is released. |
Main beam
| Main beam can be activated when the steering wheel stalk switch’s rotating ring is in position AUTO or | |
| Deactivate by moving the stalk switch backwards. |
Note
When main beam has been activated, it can be deactivated by moving the stalk switch backwards to either
When main beam has been activated the
Using the guidance light
Some of the exterior lighting can be kept switched on to work as guidance light after the car has been locked.
To activate the function:
- Make sure the car is switched off.
- Move the left-hand stalk switch forward toward the instrument panel and release.
- Get out of the car and lock the door.
The
The guidance light is illuminated for approximately 60 seconds.
Adapting the headlamp pattern from the headlamps
This car does not need to reset the headlamp pattern when changing from right to left-hand traffic, and vice versa.
Emergency brake lights
- Emergency brake lights are activated to alert vehicles behind about heavy braking.
- The function means that the brake light flashes instead of – as in normal braking – shining with a constant glow.
- The emergency brake lights are activated during heavy braking or if the ABS system is activated at high speeds.
- After the driver brakes to a low speed and then releases the brake, the brake light returns to normal function and is extinguished.
- The car’s hazard warning flashers are activated at the same time. These flash until the driver accelerates the car to a higher speed again or switches off the car’s hazard warning flashers.
Position lamps
Position lamps can be used so that other road users can see the car if it stops or is parked. The position lamp is switched on with the rotating ring on the stalk switch.
Stalk switch rotating ring in position lamps position.
- Turn the rotating ring to the
- If the car’s electrical system is in ignition position II then the daytime running lights are switched on instead of the front position lamps. When the rotating ring is in this position, the rear position lamps are switched on regardless of the ignition position of the car’s electrical system.
- If the car is stationary but running, the rotating ring can be moved to the position lamp
- When driving for more than 30 seconds at max. 10 km/h (approx. 6 mph), or if the speed exceeds 10 km/h (approx. 6 mph), the daytime running lights are switched on. The driver should turn to a position other than
- If the boot lid is opened when it is dark outside, the rear position lamps are switched on (if not already switched on) to warn road users approaching from behind. This takes place irrespective of the position of the rotating ring or the ignition position of the car’s electrical system.
Welcome light
The welcome light is switched on when the car is unlocked and is used to switch on the car’s lighting at a distance.
The function is activated when the car is unlocked. In daylight, position lamps, interior roof lamps, floor lights and cargo area lighting are activated. In weak daylight or darkness, number plate lighting and lighting in the outer handles are also activated (Option/accessory.)with their light source aimed towards the ground.
The lighting stays on for approx. 2 minutes if no doors are opened. If a door is opened within the activation time, the time for the interior lighting and lighting in the outer handles (Option/accessory.) will be extended.
The function can be activated and deactivated via the centre display.
Hazard warning flashers
Hazard warning flashers warn other road users by means of all of the car’s direction indicators being activated simultaneously. The function can be used to give a warning in the event of traffic hazards.
Button for hazard warning flashers.
- Press the button to activate the hazard warning flashers.
- The hazard warning flashers are automatically activated when the car brakes so powerfully that the emergency brake lights are activated and the speed is low. The hazard warning flashers start to flash after the emergency brake lights have stopped flashing and are then deactivated automatically when the car drives away again or are deactivated if the button is depressed.\
- The hazard warning flashers are automatically activated in the event of a collision.
Regulations for the use of hazard warning flashers may vary between countries.
Daytime running lights
The car has sensors that detect the light conditions in the surroundings. The daytime running lights are switched on when the rotating ring on the stalk switch is in position 0,
Stalk switch rotating ring in AUTO position.
If the stalk switch rotating ring is in the AUTO position, the daytime running lights {DRL(Daytime Running Lights)} are switched on when the car is driven in daylight. The car automatically changes lighting from daytime running light to dipped beam in weak daylight or darkness. Changing to dipped beam also takes place if the front fog lamp(Option/accessory.) and/or rear fog lamp are activated.
This system help to save energy – it cannot determine in all situations when daylight is too weak or sufficiently strong, e.g. in mist and rain.
The driver is always responsible for ensuring that the car is driven with the correct beam pattern for the traffic situation and in accordance with applicable traffic regulations.
Checking trailer lamps
When connecting a trailer – check that the trailer lamps work before departure.
Checking trailer lamps
Automatic checking
After a trailer is connected electrically, it is possible to ensure that the trailer lamps are working via an automatic lamp activation. The function helps the driver check that the trailer lamps are working before starting off.
- When a trailer is connected to the towbar, the Perform a trailer lamp check? message is shown in the driver display.
- Confirm the message by pressing the right-hand steering wheel keypad’s O button.
- The lamp check starts.
- Exit the car to check lamp functionality.
- All trailer lamps start to flash – then the lamps are switched on one at a time.
- Visually check that all lamps available on the trailer are operational.
- After a moment, all lamps on the trailer flash again.
- The check is complete.
Rear fog lamp on trailer
When connecting a trailer, there may be instances when the rear fog lamp on the car does not illuminate. In these cases, rear fog lamp functionality is transferred to only the trailer. Therefore, in these cases, check when the rear fog lamp is activated that the trailer is equipped with rear fog lamp in order to drive the vehicle combination in a safe manner.
Symbols and messages in the driver display
If one or more of the trailer’s direction indicators or brake light bulbs is broken, the driver display shows a symbol and a message. Other lights on the trailer must be checked manually by the driver before setting off.
| Symbol | Message |
|---|---|
| | Right trailer turn indicator malfunction Left trailer turn indicator malfunction |
| | Trailer brake light malfunction |
If any lamp for the trailer’s direction indicators is broken, the driver display symbol for direction indicators will also flash more quickly than normal.