The multi-information display presents the driver with a variety of driving-related data, such as the current outside temperature. The multi-information display can also be used to change the display settings and other settings.
The content display area is operated using the meter control switches.
When the screen can be scrolled or different content can be displayed, a mark, such as an arrow, will be displayed to suggest which switch to operate.
Items in this area are operated using the “ODO/TRIP” switch.
Select a menu icon to display its content.
Use the displayed fuel consumption as a reference only.
Speedometer
Displays the vehicle speed.
Blank (No items)
Displays no drive information contents.
Use the meter control switches on the steering wheel to change settings.
LTA (Lane Tracing Assist)
The following LTA system settings can be changed:
Item | Settings | Details |
Lane center | On | Select to enable/disable the lane centering function. |
Off | ||
Alert sensitivity | High | Select to set the warning sensi- tivity. |
Std. | ||
Sway warning | On | Select to enable/disable the vehi- cle sway warning. |
Off | ||
Sway sensitivity | High | Select to set the vehicle sway warning sensitivity. |
Std. | ||
Low |
PCS (Pre-Collision System)
The following pre-collision system settings can be changed:
Item | Settings | Details | |
PCS | On | Select to enable/disable the pre- collision system. | |
Off | |||
Warning sensitivity | Early | Select to change the warning timing. | |
Middle | |||
Late |
DRCC (Dynamic Radar Cruise Control)
Item | Settings | Details | |
Curve speed reduction | | Strong | Select to change the vehicle speed reduction strength. |
| Weak | ||
Off |
BSM (Blind Spot Monitor) function (if equipped)
Item | Settings | Details |
BSM | On | Select to enable/disable the Blind Spot Monitor function. |
Off |
RCTA (Rear Cross Traffic Alert) function (if equipped)
Item | Settings | Details |
RCTA | On | Select to enable/disable the Rear Cross Traffic Alert function. |
Off |
RCD (Rear Camera Detection) function (if equipped)
Item | Settings | Details |
RCD | On | Select to enable/disable the rear camera detection. |
Off |
RSA (Road Sign Assist) (if equipped) (P. 285)
The following RSA settings can be changed:
Item | Settings | Details | ||||
RSA | On | Select RSA. | to | enable/disable | the | |
Off | ||||||
Notification method |
Excess notification |
speed | Select a notification method used to warn the driver if the vehicle speed exceeds the speed dis- played on the speed limit sign on the multi-information display. Available methods: • No notification • Display only • Display and buzzer | |||
Other notifications | Select a notification method used to warn the driver if the system detects the vehicle approaching to the no-entry road when a do not enter sign is displayed on the multi-information display. Available methods: • No notification • Display only • Display and buzzer | |||||
Excess speed noti- fication level | 5 mph (10 km/h) | Select a speed threshold over which the excess speed notifica- tion will start to operate when a speed limit sign is displayed on the multi-information display. | ||||
3 mph (5 km/h) | ||||||
1 mph (2 km/h) |
Item | Settings | Details | |
BSM (Blind Spot Monitor) (if equipped) (®P. 330) | |||
Outside rear view mirror indicator brightness | Bright | Select to change the brightness of the outside rearview mirror indicators. | |
Dim | |||
Notification timing for the presence of approaching vehi- cle (sensitivity) | | Early |
Select to change the notification timing for an approaching vehicle. |
| Middle | ||
| Late | ||
Only when vehicle detected in blind spot | |||
RCTA (Rear Cross Traffic Alert) (if equipped) | |||
RCTA buzzer vol- ume | 1 (Low) | Select to change the volume of the RCTA buzzer. | |
2 (Medium) | |||
3 (Loud) | |||
TPWS (Tire pressure warning system) (®P. 474) | |||
Set pressure (tire pressure warning sys- tem initialization) | Select to initialize the tire pres- sure warning system. To per- form initialization, press and hold the Before performing initialization, make sure to adjust the inflation pressure of each tire to the spec- ified level. | ||
Change wheel (change the tire pres- sure warning system sensor ID code set) (vehicles without a tire inflation pres- sure display function) | Select to change the tire pres- sure warning system sensor ID code set. To enable this function, a second set of tire pressure warning sys- tem sensor ID codes must be registered by a Toyota dealer. For information regarding chang- ing the registered ID code set, contact your Toyota dealer.
|
Item | Settings | Details |
Change wheel (register tire pressure warning system sensor ID codes) (vehicles with a tire inflation pressure display function) | Select to register the ID codes of the tire pressure sensors to the tire pressure warning system. To register the ID codes, press and hold the | |
Rear seat reminder (®P. 154) | On | Select to enable/disable the rear seat reminder. |
Off | ||
Scheduled maintenance display (if equipped) | ||
Maintenance data reset | Select to reset the message indi- cating maintenance is required, after the required maintenance is performed. (®P. 448) |
Item | Settings | Details |
Language | Select to change the language displayed. | |
Units | Select to change the units of measure displayed. | |
(Eco Driving Indicator Light) | On | Select to enable/disable the Eco Driving Indicator Light. |
Off | ||
Drive information (total [after reset]) | Average vehicle speed | Select to change the display between average speed/elapsed time. |
Elapsed time | ||
Pop-up display | Incoming calls | Select to enable/disable the pop- up display. |
Brightness adjust- ment | ||
Default setting | Select to reset the meter display settings to the default setting. |
Displays suggestions to the driver in the following situations. To select a response to a displayed suggestion, use the meter control switches.
Eco Driving Indicator
Eco Driving Indicator Light
Suspension of the settings display
Tire pressure (vehicles with a tire inflation pressure display function)
Liquid crystal display
Small spots or light spots may appear on the display. This phenomenon is characteristic of liquid crystal displays, and there is no problem continuing to use the display.
Customization
Some functions can be customized.
WARNING
NOTICE
While setting up the display To prevent battery discharge, ensure that the engine is running while setting up the display features.
Access the comprehensive 2010-2018 VW Jetta Passenger Fuse Box Diagram to troubleshoot electrical issues effectively.…
Explore the comprehensive VW Jetta Passenger Fuse Box Diagram to troubleshoot electrical issues effectively. Understand…
Under Hood Fuse Box Location Remove the front luggage compartment cover. Under Hood Fuse Box…
2022 Kawasaki NINJA H2 SX SE Brake Lever Adjuster Owner's Manual NOTICE Only adjust the front…
2023 Land Rover Range Rover Evoque Exiting The Vehicle SINGLE LOCKING WARNING Before exiting the…
2023 Land Rover Range Rover Evoque Front Seats FRONT SEAT SAFETY Make sure to read…