2022 Toyota Camry Do-It-Yourself Maintenance User Manual

2022 Toyota Camry Do-It-Yourself Maintenance

Do-it-yourself service precautions

If you perform maintenance by yourself, be sure to follow the correct procedure as given in these sections.

Items	Parts and tools
Battery condition (®P. 469)	•    Warm water       • Baking soda      • Grease •    Conventional wrench (for terminal clamp bolts)
Brake fluid level (®P. 468)	•    FMVSS No.116 DOT 3 or SAE J1703 brake fluid •    Rag or paper towel •    Funnel (used only for adding brake fluid)
Engine     coolant level (®P. 466)	•    “Toyota Super Long Life Coolant” or a similar high quality ethylene glycol-based non-silicate, non- amine, non-nitrite and non-borate coolant with long- life hybrid organic acid technology U.S.A.: “Toyota Super Long Life Coolant” is pre-mixed with 50% coolant and 50% deionized water. Canada: “Toyota Super Long Life Coolant” is pre-mixed with 55% coolant and 45% deionized water. •    Funnel (used only for adding engine coolant)
Engine oil level (®P. 462)	•    “Toyota Genuine Motor Oil” or equivalent •    Rag or paper towel •    Funnel (used only for adding engine oil)
Fuses (®P. 499)	•    Fuse with same amperage rating as original
Light bulbs (®P. 502)	•    Bulb with same number and wattage rating as origi- nal •    Flathead screwdriver       • Wrench
Radiator/con- denser (®P. 467)	¾
Tire         inflation pressure (®P. 487)	•   Tire pressure gauge •   Compressed air source
Washer fluid (®P. 472)	•    Water or washer fluid containing antifreeze (for win- ter use) •    Funnel (used only for adding water or washer fluid)

WARNING

The engine compartment contains many mechanisms and fluids that may move suddenly, become hot, or become electrically energized. To avoid death or serious injury, observe the following precautions.

1. When working on the engine compartment
   1. Keep hands, clothing, and tools away from the moving fan and engine drive belt.
   2. Be careful not to touch the engine, radiator, exhaust manifold, etc. right after driving as they may be hot. Oil and other fluids may also be hot.
   3. Do not leave anything that may burn easily, such as paper and rags, in the engine compartment.
   4. Do not smoke, cause sparks or expose an open flame to fuel or the battery. Fuel and battery fumes are flammable.
   5. Be extremely cautious when working on the battery. It contains poisonous and corrosive sulfuric acid.
2. When working near the electric cooling fan or radiator grille
   1. Vehicles without a smart key system: Be sure the engine switch is off. With the engine switch in the “ON” position, the electric cooling fan may automatically start to run if the air conditioning is on and/or the coolant temperature is high. (P. 467)
   2. Vehicles with a smart key system: Be sure the engine switch is off. With the engine switch in IGNITION ON mode, the electric cooling fan may automatically start to run if the air conditioning is on and/or the coolant temperature is high. (P. 467)
3. Safety glasses
   1. Wear safety glasses to prevent flying or falling material, fluid spray, etc. from getting in your eyes.

NOTICE

If you remove the air cleaner filter Driving with the air cleaner filter removed may cause excessive engine wear due to dirt in the air.

Hood

Release the lock from the inside of the vehicle to open the hood.

1. Pull the hood lock release lever. The hood will pop up slightly.
2. Pull up the auxiliary catch lever and lift the hood.
3. Hold the hood open by inserting the support rod into the slot.

Open hood warning buzzer

If the vehicle reaches a speed of 3 mph (5 km/h), the master warning light flashes, and a buzzer sounds to indicate that the hood is not fully closed.

WARNING

1. Pre-driving check
   1. Check that the hood is fully closed and locked.
   2. If the hood is not locked properly, it may open while the vehicle is in motion and cause an accident, which may result in death or serious injury.
2. After installing the support rod into the slot
   1. Make sure the rod supports the hood securely preventing it from falling down onto your head or body.

NOTICE

When closing the hood Be sure to return the support rod to its clip before closing the hood. Closing the hood with the support rod not clipped could cause the hood to bend.

Positioning a floor jack

When using a floor jack, follow the instructions in the manual provided with the jack and perform the operation safely. When raising your vehicle with a floor jack, position the jack cor-rectly. Improper placement may damage your vehicle or cause injury.

Front

Rear

• 2WD models
• AWD models

Engine compartment

2.5 L 4-cylinder (A25A-FKS) engine

1. Fuse boxes (if equipped) (P. 499)
2. Engine oil filler cap (P. 464)
3. Engine oil level dipstick (P. 462)
4. Brake fluid reservoir (P. 468)
5. Battery (P. 469)
6. Radiator (P. 467)
7. Electric cooling fan
8. Condenser (P. 467)
9. Engine coolant reservoir (P. 466)
10. Washer fluid tank (P. 472)

3.5 L V6 (2GR-FKS) engine

1. Fuse boxes (if equipped) (P. 499)
2. Engine oil filler cap (P. 464)
3. Engine oil level dipstick (P. 462)
4. Brake fluid reservoir (P. 468)
5. Battery (P. 469)
6. Radiator (P. 467)
7. Electric cooling fan
8. Condenser (P. 467)
9. Engine coolant reservoir (P. 466)
10. Washer fluid tank (P. 472)

Engine oil

With the engine at operating temperature and turned off, check the oil level on the dipstick.

Checking the engine oil

1. Park the vehicle on level ground. After warming up the engine and turning it off, wait more than 5 minutes for the oil to drain back into the bottom of the engine.
2. Holding a rag under the end, pull the dipstick out.
   1. 2.5 L 4-cylinder (A25A-FKS) engine
   2. 3.5 L V6 (2GR-FKS) engine
3. Wipe the dipstick clean.
4. Reinsert the dipstick fully.
5. Holding a rag under the end, pull the dipstick out and check the oil level.
   1. Flat dipstick
   2. Twist dipstick
      1. Low
      2. Normal
      3. Excessive
         1. The shape of the dipstick may differ depending on the type of vehicle or engine.
6. Wipe the dipstick and reinsert it fully.

Adding engine oil

If the oil level is below or near the low-level mark, add engine oil of the same type as that already in the engine.

Engine oil selection	®P. 578
Oil quantity (Low ® Full)	u 2.5 L 4-cylinder (A25A-FKS) engine 1.6 qt. (1.5 L, 1.3 Imp. qt.) u 3.5 L V6 (2GR-FKS) engine 1.9 qt. (1.8 L, 1.6 lmp. qt.)
Items	Clean funnel

Make sure to check the oil type and prepare the items needed before adding oil.

1. Remove the oil filler cap by turning it counterclockwise.
2. Add engine oil slowly, checking the dipstick.
3. Install the oil filler cap by turning it clockwise.

Engine oil consumption

A certain amount of engine oil will be consumed while driving. In the following situations, oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals.

• When the engine is new, for example directly after purchasing the vehicle or after replacing the engine
• If low-quality oil or oil of an inappropriate viscosity is used
• When driving at high engine speeds or with a heavy load, or when driving while accelerating or decelerating frequently
• When leaving the engine idling for a long time, or when driving frequently through heavy traffic

WARNING

• Used engine oil
  • Used engine oil contains potentially harmful contaminants which may cause skin disorders such as inflammation and skin cancer, so care should be taken to avoid prolonged and repeated contact. To remove used engine oil from your skin, wash thoroughly with soap and water.
  • Dispose of used oil and filters only in a safe and acceptable manner. Do not dispose of used oil and filters in household trash, in sewers, or onto the ground.
    • Call your Toyota dealer, service station, or auto parts store for information concerning recycling or disposal.
  • Do not leave used engine oil within the reach of children.

NOTICE

• To prevent serious engine damage
  • Check the oil level on a regular basis.
• When replacing the engine oil
  • Be careful not to spill engine oil on the vehicle components.
  • Avoid overfilling, or the engine could be damaged.
  • Check the oil level on the dipstick every time you refill the vehicle.
  • Be sure the engine oil filler cap is properly tightened.
• If oil is spilled on the engine cover (2.5 L 4-cylinder [A25A-FKS] engine) To prevent the engine cover from being damaged, remove any engine oil from the engine cover as soon as possible using a neutral detergent.
  • Do not use an organic solvent such as brake cleaner.

Engine coolant

The coolant level is satisfactory if it is between the “F” and “L” lines on the reservoir when the engine is cold.

• Reservoir cap
• “F” line
• “L” line
  • If the level is on or below the “L” line, add coolant up to the “F” line. (P. 567)

Coolant selection

Only use “Toyota Super Long Life Coolant” or a similar high-quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology.

• U.S.A.:
  • “Toyota Super Long Life Coolant” is a mixture of 50% coolant and 50% deionized water. (Minimum temperature: -31F [-35 C])
• Canada:
  • “Toyota Super Long Life Coolant” is a mixture of 55% coolant and 45% deionized water. (Minimum temperature: -44F [-42 C])

For more details about engine coolant, contact your Toyota dealer.

If the coolant level drops within a short time of replenishing

Visually check the radiator, hoses, engine coolant reservoir caps, drain cock, and water pump. If you cannot find a leak, have your Toyota dealer test the cap and check for leaks in the cooling system.

WARNING

When the engine is hot Do not remove the engine coolant reservoir cap or the radiator cap. The cooling system may be under pressure and may spray hot coolant if the cap is removed, causing serious injuries, such as burns.

NOTICE

• When adding coolant
  • Coolant is neither plain water nor straight antifreeze. The correct mixture of water and antifreeze must be used to provide proper lubrication, corrosion protection, and cooling. Be sure to read the antifreeze or coolant label.
• If you spill coolant
  • Be sure to wash it off with water to prevent it from damaging parts or paint.

Radiator and condenser

Check the radiator and condenser and clear away any foreign objects. If either of the above parts is extremely dirty or you are not sure of their condition, have your vehicle inspected by your Toyota dealer.

WARNING

When the engine is hot Do not touch the radiator or condenser as they may be hot and cause serious injuries, such as burns.

Brake fluid

Checking fluid level

The brake fluid level should be between the “MAX” and “MIN” lines on the tank.

1. “MAX”
2. “MIN”

Adding fluid

Make sure to check the fluid type and prepare the necessary item.

Fluid type	FMVSS No.116 DOT 3 or SAE J1703 brake fluid
Item	Clean funnel

Brake fluid can absorb moisture from the air Excess moisture in the brake fluid can cause a dangerous loss of braking efficiency. Use only newly opened brake fluid.

WARNING

When filling the reservoir Take care as brake fluid can harm your hands and eyes and damage painted surfaces. If fluid gets on your hands or in your eyes, flush the affected area with clean water immediately. If you still experience discomfort, see a doctor.

NOTICE

If the fluid level is low or high It is normal for the brake fluid level to go down slightly as the brake pads wear out or when the fluid level in the accumulator is high. If the reservoir needs frequent refilling, there may be a serious problem.

Battery

Check the battery as follows.

Battery exterior

Make sure that the battery terminals are not corroded and that there are no loose connections, cracks, or loose clamps.

• Terminals
• Hold-down clamp

Before recharging

When recharging, the battery produces hydrogen gas which is flammable and explosive. Therefore, observe the following before recharging:

• If recharging with the battery installed on the vehicle, be sure to disconnect the ground cable.
• Make sure the power switch on the charger is off when connecting and disconnecting the charger cables to the battery.

After recharging/reconnecting the battery (vehicles with a smart key system)

• Unlocking the doors using the smart key system may not be possible immediately after reconnecting the battery. If this happens, use the wireless remote control or the mechanical key to lock/unlock the doors.
• Start the engine with the engine switch in ACCESSORY mode. The engine may not start with the engine switch turned off. However, the engine will operate normally from the second attempt.
• The engine switch mode is recorded by the vehicle. If the battery is reconnected, the vehicle will return the engine switch mode to the status it was in before the battery was disconnected. Make sure to turn off the engine before disconnecting the battery. Take extra care when connecting the battery if the engine switch mode prior to discharge is unknown

If the system will not start even after multiple attempts, contact your Toyota dealer.

WARNING

1. Chemicals in the battery Batteries contain poisonous and corrosive sulfuric acid and may produce hydrogen gas which is flammable and explosive. To reduce the risk of death or serious injury, take the following precautions while working on or near the battery:
   1. Do not cause sparks by touching the battery terminals with tools.
   2. Do not smoke or light a match near the battery.
   3. Avoid contact with eyes, skin, and clothes.
   4. Never inhale or swallow electrolytes.
   5. Wear protective safety glasses when working near the battery.
   6. Keep children away from the battery.
2. Where to safely charge the battery
   1. Always charge the battery in an open area. Do not charge the battery in a garage or closed room where there is insufficient ventilation.
3. How to recharge the battery
   1. Only perform a slow charge (5 A or less). The battery may explode if charged at a quicker rate.
4. Emergency measures regarding electrolyte
   1. If electrolyte gets in your eyes
      1. Flush your eyes with clean water for at least 15 minutes and get immediate medical attention. If possible, continue to apply water with a sponge or cloth while traveling to the nearest medical facility.
   2. If electrolyte gets on your skin
      1. Wash the affected area thoroughly. If you feel pain or burning, get medical attention immediately.
   3. If electrolyte gets on your clothes
      1. It can soak through clothing onto your skin. Immediately take off the clothing and follow the procedure above if necessary.
   4. If you accidentally swallow an electrolyte
      1. Drink a large quantity of water or milk. Get emergency medical attention immediately.
5. When disconnecting the battery
   1. Do not disconnect the negative (-) terminal on the body side. The disconnected negative (-) terminal may touch the positive (+) terminal, which may cause a short and result in death or serious injury.

NOTICE

When recharging the battery Never recharge the battery while the engine is running. Also, be sure all accessories are turned off.

Washer fluid

Add washer fluid in the following situations:

• A washer does not work.
• “Windshield Washer Fluid Low” is displayed on the multi-information display.

WARNING

When adding washer fluid  Do not add washer fluid when the engine is hot or running as washer fluid contains alcohol and may catch fire if spilled on the engine, etc.

NOTICE

• Do not use any fluid other than washer fluid
  • Do not use soapy water or engine antifreeze instead of washer fluid. Doing so may cause streaking on the vehicle’s painted surfaces, as well as damaging the pump leading to problems of the washer fluid not spraying.
• Diluting washer fluid
  • Dilute washer fluid with water as necessary.
  • Refer to the freezing temperatures listed on the label of the washer fluid bottle.

Tires

Replace or rotate tires in accordance with maintenance schedules and treadwear.

Checking tires

Check if the tread wear indicators are showing on the tires. Also check the tires for uneven wear, such as excessive wear on one side of the tread. Check the spare tire condition and pressure if not rotated.

1. New thread
2. Worn tread
3. Treadwear indicator
4. The location of treadwear indicators is shown by a “TWI” or “” mark, etc., molded into the sidewall of each tire.
   1. Replace the tires if the tread wear indicators are showing on a tire.

Tire rotation

Rotate the tires in the order shown. To equalize tire wear and extend tire life, Toyota recommends that tire rotation is carried out at the same interval as tire inspection.
Do not fail to initialize the tire pressure warning system after a tire rotation.

Tire pressure warning system

Your vehicle is equipped with a tire pressure warning system that uses a tire pressure warning valve and transmitters to detect low tire inflation pressure before serious problems arise.

• Vehicles without a tire inflation pressure display function
  • If the tire pressure drops below a predetermined level, the driver is warned by a warning light. (P. 531)
• Vehicles with a tire inflation pressure display function
  • The tire pressure detected by the tire pressure warning system can be displayed on the multi-information display.
    • 4.2-inch display
    • 7-inch display
  • If the tire pressure drops below a predetermined level, the driver is warned by a screen display and a warning light. (P. 531)
    • 4.2-inch display
    • 7-inch display

Installing tire pressure warning valve and transmitters

• When replacing the tires or wheels, the tire pressure warning valve and transmitters must be installed on the wheels which will be installed in the vehicle.
• When new tire pressure warning valves and transmitters are installed, new ID codes must be registered in the tire pressure warning computer and the tire pressure warning system must be initialized. (P. 477)

Initializing the tire pressure warning system

1. The tire pressure warning system must be initialized in the following circumstances:
   1. When the tire inflation pressure is changed such as when changing traveling speed or load weight.
   2. When the tire inflation pressure is changed such as when the tire size is changed.
   3. When rotating the tires.
   4. Vehicles with a tire inflation pressure display function: After performing the transmitter ID code registration procedure. (P. 477)

When the tire pressure warning system is initialized, the current tire inflation pressure is set as the benchmark pressure.

How to initialize the tire pressure warning system

1. Park the vehicle in a safe place and stop the engine for 20 minutes or more.
   1. The initialization procedure cannot be started while the vehicle is moving.
2. Adjust the tire inflation pressure to the specified cold tire inflation pressure level. (P. 584)
   1. Make sure to adjust the tire pressure to the specified cold tire inflation pressure level. The tire pressure warning system will operate based on this pressure level.
3. Start the engine. (P. 209, 211)
4. Select  (4.2-inch display) or (7-inch display) on the multi-information display using the meter control switches on the steering wheel. (P. 103, 117).
5. 4.2-inch display: Select “Vehicle Settings” and then press 7-inch display: Select and then press and hold .
6. Select “TPWS” and then press
7. Select “Set Pressure” then press and hold until the tire pressure warning light blinks 3 times.
   1. Then a message will be displayed on the multi-information display.
   2. Vehicles with a tire inflation pressure display function: “- -” will be displayed on the multi-information display for the inflation pressure of each tire while initialization is being performed.
8. Vehicles with a tire inflation pressure display function: Drive at approximately 25 mph (40 km/h) or more for approximately 10 to 30 minutes.
   1. When initialization is complete, the inflation pressure of each tire will be displayed on the multi-information display.
   2. Even if the vehicle is not driven at approximately 25 mph (40 km/h) or more, initialization can be completed by driving for a long time. However, if initialization does not complete after driving for 1 hour or more, park the vehicle in a safe place for approximately 20 minutes and then drive the vehicle again.

Registering ID codes

Vehicles without a tire inflation pressure display function

• Every tire pressure warning valve and transmitter has a unique ID code. In addition to the set of tire pressure warning system sensor ID codes initially registered to the vehicle, the second set of ID codes can be registered.
• The second set of tire pressure warning system sensor ID codes can be registered at your Toyota dealer. When 2 sets of ID codes have been registered, either ID code set can be selected.

Vehicles with a tire inflation pressure display function

Every tire pressure warning valve and transmitter has a unique ID code. When replacing a tire pressure warning valve and transmitter, it is necessary to register the ID codes. The ID codes can be registered on  (a 4.2-inch display) or  (a 7-inch display) of the multi-information display.

Changing the available set of ID codes (vehicles without a tire inflation pressure display function)

• When 2 sets of ID codes are registered, the corresponding ID code set for the installed wheels can be selected on  (4.2-inch display) or  (7-inch display) of the multi-information display. It is not necessary to reregister the ID codes each time the wheels are changed.
• For information regarding changing the registered ID codes for an ID code set, contact your Toyota dealer.

How to register the ID codes (vehicles with a tire inflation pres-sure display function)

1. Park the vehicle in a safe place, wait for approximately 20 minutes, and then start the engine. (P. 209, 211)
   Select  (4.2-inch display) or (7-inch display) on the multi-information display using the meter control switches on the steering wheel. (P. 103, 117)
2. 4.2-inch display: Select  “Vehicle Settings” and then press . 7-inch display: Select and then press and hold .
3. Select “TPWS” and then press
4. Select “Change Wheel” then press and hold until the tire pressure warning light blinks slowly 3 times.
   1. Then a message will be displayed on the multi-information display.
   2. When registration is being performed, the tire pressure warning light will blink for approximately 1 minute then illuminate, and “- -” will be displayed for the inflation pres-sure of each tire on the multi-information display.
5. Drive at approximately 25 mph (40 km/h) or more for approximately 10 to 30 minutes.
   1. Registration is complete when the tire pressure warning light turns off and the inflation pressure of each tire is displayed on the multi-information display.
   2. Even if the vehicle is not driven at approximately 25 mph (40 km/h) or more, registration can be completed by driving for a long time. However, if registration does not complete after driving for 1 hour or more, perform the procedure again from the beginning. Initialize the tire pressure warning system. (P. 475)

When to replace your vehicle’s tires

Tires should be replaced if:

• The treadwear indicators are showing on a tire.
• You have tire damage such as cuts, splits, cracks deep enough to expose the fabric, and bulges indicating internal damage
• A tire goes flat repeatedly or cannot be properly repaired due to the size or location of a cut or other damage

If you are not sure, consult with your Toyota dealer.

Replacing tires and wheels

If the ID codes of the tire pressure warning valve and transmitters are not registered, the tire pressure warning system will not work properly. In this case, after driving for about 20 minutes, the tire pressure warning light will blink for approximately 1 minute and then illuminate to indicate a system malfunction.

Tire life

Any tire over 6 years old must be checked by a qualified technician even if it has seldom or never been used or damage is not obvious.

Routine tire inflation pressure checks

The tire pressure warning system does not replace routine tire inflation pressure checks. Make sure to check tire inflation pressure as part of your routine of daily vehicle checks.

Low profile tires (vehicles with 18 or 19-inch wheels)

Generally, low-profile tires will wear more rapidly and tire grip performance will be reduced on snowy and/or icy roads when compared to standard tires. Be sure to use snow tires on snowy and/or icy roads and drive carefully at a speed appropriate for road and weather conditions.

Maximum load of the tire

• Check that the maximum load of the replacement tire is greater than 1/2 of the Gross Axle Weight Ratings (GAWR) of either the front axle or the rear axle, whichever is greater.
• For the GAWR, see the Certification Label. For the maximum load of the tire, see the load limit at the maximum cold tire inflation pressure mentioned on the sidewall of the tire. (P. 593)

Tire types

• Summer tires
  • Summer tires are high-speed performance tires best suited to highway driving under dry conditions. Since summer tires do not have the same traction performance as snow tires, summer tires are inadequate for driving on snow-covered or icy roads. For driving on snow-covered roads or icy roads, the use of snow tires is recommended. When installing snow tires, be sure to replace all four tires.
• All season tires
  • All-season tires are designed to provide better traction in snow and to be adequate for driving in most winter conditions as well as for use year-round. All-season tires, however, do not have adequate traction performance compared with snow tires in heavy or loose snow. Also, all-season tires fall short in acceleration and handling performance compared with summer tires in highway driving.
• Snow tires
  • For driving on snow-covered roads or icy roads, we recommend using snow tires. If you need snow tires, select tires of the same size, construction, and load capacity as the originally installed tires. Since your vehicle has radial tires as original equipment, make sure your snow tires also have radial construction. Do not install studded tires without first checking local regulations for possible restrictions. Snow tires should be installed on all wheels. (P. 377)

If the tread on snow tires wears down below 0.16 in. (4 mm)

The effectiveness of the tires as snow tires is lost.

Situations in which the tire pressure warning system may not operate properly

• In the following situations, the tire pressure warning system may not operate properly.
  • If non-genuine Toyota wheels are used.
  • If a tire has been replaced with a tire that is not an OE (Original Equipment) tire.
  • If a tire has been replaced with a tire that is not of the specified size.
  • If tire chains, etc. are installed.
  • If a window tint that affects radio wave signals is installed.
  • If there is a lot of snow or ice on the vehicle, particularly around the wheels or wheel housings.
  • If the tire inflation pressure is much higher than the specified level.
  • If wheels not equipped with tire pressure warning valve and transmitter are used.
  • If the ID codes of the tire pressure warning valve and transmitters are not registered in the tire pressure warning computer.
• Performance may be affected in the following situations.
  • When driving near a TV tower, electric power plant, gas station, radio station, large display, airport or another facility that generates strong radio waves or electrical noise
  • When carrying a portable radio, cellular phone, cordless phone, or other wireless communication device Vehicles with a tire inflation pressure display function: If tire position information is not correctly displayed due to the radio wave conditions, the display may be corrected by changing the location of the vehicle as the radio wave conditions may change.
• When the vehicle is stopped, the time taken for the warning to start or turn off maybe longer.
• When the inflation pressure of a tire drops rapidly, for example when a tire has burst, the warning may not operate.

Initialization procedure

• Make sure to perform the initialization procedure after adjusting the tire inflation pressure.
  • Also, make sure the tires are cold before performing the initialization procedure or adjusting the tire inflation pressure.
• If the engine switch is turned to the “LOCK” position (vehicles without a smart key system) or off (vehicles with a smart key system) during initialization, it is not necessary to restart the initialization procedure from the beginning as it will begin automatically when the engine switch is turned back to the “ON” position (vehicles without a smart key system) or IGNITION ON mode (vehicles with a smart key system).
• If initialization has accidentally been started when it is not necessary, adjust the tire inflation pressure to the specified level when the tires are cold and then perform the initialization procedure again.
• Vehicles with a tire inflation pressure display function: While the position of each tire is being determined and the inflation pressures are not being displayed on the multi-information display, if the inflation pressure of a tire drops, the tire pressure warning light will come on.

Warning performance of the tire pressure warning system

The warning of the tire pressure warning system will change in accordance with the conditions under which it was initialized. For this reason, the system may give a warning even if the tire pressure does not reach a low enough level, or if the pressure is higher than the pressure that was adjusted to when the system was initialized.

If the tire pressure warning system is not initialized properly

Vehicles without a tire inflation pressure display function Initialization can be completed in a few minutes. However, in the following cases, the settings have not been recorded and the system will not operate properly. If repeated attempts to record tire inflation pressure settings are unsuccessful, have the vehicle inspected by your Toyota dealer.

• If initialization is attempted and the tire pressure warning light does not blink 3 times.
• If, when the vehicle has been driven for about 20 minutes after performing initialization, the tire pressure warning light blinks for approximately 1 minute and then illuminates.

Vehicles with a tire inflation pressure display function

• In the following situations, initialization may take longer than usual to be completed or may not be possible. (Usually, the vehicle will need to be driven for approximately 10 to 30 minutes to complete initialization.) If initialization is not complete after driving approximately 30 minutes, continue driving for a while.
  • If the vehicle is driven on an unpaved road, it may take longer to complete initialization.
  • If the vehicle is backed up while performing initialization, data collected during initialization will be cleared and it will take longer than normal to complete.
  • If the vehicle is driven in heavy traffic or another situation where other vehicles are driven close by, it may take time for the system to recognize the tire pressure warning valve and transmitters of your vehicle over those of other vehicles.

If initialization is not complete after driving for approximately 1 hour, park the vehicle in a safe place for approximately 20 minutes and then drive the vehicle again.

• In the following situations, initialization will not be started or was not completed properly and the system will not operate properly. Perform the initialization procedure again.
  • If, when attempting to start initialization, the tire pressure warning light does not blink 3 times.
  • If, when the vehicle has been driven for about 20 minutes after performing initialization, the tire pressure warning light blinks for approximately 1 minute and then illuminates.
• If initialization cannot be completed after performing the above procedure, contact your Toyota dealer.

When registering ID codes (vehicles with a tire inflation pressure dis-play function)

• Before performing ID code registration, make sure that no wheels with tire pressure warning valve and transmitters installed are near the vehicle.
• Make sure to initialize the tire pressure warning system after registering the ID codes. If the system is initialized before registering the ID codes, the initialized values will be invalid.
• As the tires will be warm when registration is completed, make sure to allow the tires to cool before performing initialization.

Canceling ID code registration (vehicles with a tire inflation pressure display function)

• To cancel ID code registration after it has been started, turn the engine switch off before driving the vehicle.
  • If the vehicle is driven after ID code registration is started, cancel the registration, perform the ID code registration start the procedure again, and turn the engine switch off before driving.
• If ID code registration has been canceled, the tire pressure warning light will blink for approximately 1 minute when the engine switch is turned to the “ON” position (vehicles without a smart key system) or
  • IGNITION ON mode (vehicles with a smart key system) and then illuminate. The tire pressure warning system will be operational when the tire pressure warning light turns off.
• If the warning light does not turn off even after several minutes have elapsed, ID code registration may not have been canceled correctly. To cancel the registration, perform the ID code registration start procedure again and then turn the engine switch off before driving.

 If ID codes are not registered properly (vehicles with a tire inflation pressure display function)

• In the following situations, ID code registration may take longer than usual to be completed or may not be possible. (Usually, the vehicle will need to be driven for approximately 10 to 30 minutes to complete ID code registration.) If ID code registration is not complete after driving for approximately 30 minutes, continue driving for a while.
  • If the vehicle is driven on an unpaved road, it may take longer than normal to complete registration.
  • If the vehicle is backed up while performing registration, data collected during registration will be cleared, and it will take longer than normal to complete.
  • If the vehicle is driven in heavy traffic or another situation where other vehicles are driven close by, it may take time for the system to recognize the tire pressure warning valve and transmitters of your vehicle over those of other vehicles.
  • If a wheel with a tire pressure warning valve and transmitter installed is inside or near the vehicle, registration of the ID codes for the installed wheels may not be possible. If ID registration is not complete after driving for approximately 1 hour, park the vehicle in a safe place for approximately 20 minutes and then perform the ID code registration procedure again.
• In the following situations, ID code registration will not be started or was not completed properly and the system will not operate properly. Perform the ID code registration procedure again.
  • If, when attempting to start ID code registration, the tire pressure warning light does not blink slowly 3 times.
  • If, when the vehicle has been driven for about 20 minutes after performing ID code registration, the tire pressure warning light blinks for approximately 1 minute and then illuminates.
• If ID code registration cannot be completed after performing the above procedure, contact your Toyota dealer.

WARNING

• When inspecting or replacing tires Observe the following precautions to prevent accidents.
  Failure to do so may cause damage to parts of the drive train as well as dangerous handling characteristics, which may lead to an accident resulting in death or serious injury.
  • Do not mix tires of different makes, models, or tread patterns.
    • Also, do not mix tires of remarkably different treadwear.
  • Do not use tire sizes other than those recommended by Toyota.
  • Do not mix differently constructed tires (radial, bias-belted, or bias-ply tires).
  • Do not mix summer, all-season, and snow tires.
  • Do not use tires that have been used on another vehicle.
    Do not use tires if you do not know how they were used previously.
• When initializing the tire pressure warning system
  • Do not initialize the tire pressure warning system without first adjusting the tire inflation pressure to the specified level. Otherwise, the tire pressure warning light may not come on even if the tire inflation pressure is low, or it may come on when the tire inflation pressure is actually normal.

NOTICE

• Repairing or replacing tires, wheels, tire pressure warning valves, transmitters, and tire valve caps
  • When removing or fitting the wheels, tires, or the tire pressure warning valve and transmitters, contact your Toyota dealer as the tire pressure warning valve and transmitters may be damaged if not handled correctly.
  • Make sure to install the tire valve caps. If the tire valve caps are not installed, water may enter the valves of the tire pressure warning valve and transmitters and the valves may become stuck.
  • When replacing tire valve caps, do not replace them with metal caps or any tire valve caps other than specified, as they may become stuck.
• To avoid damage to the tire pressure warning valve and transmitters
  • When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or another qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and transmitter when replacing the tire. (P. 475)
• Driving on rough roads
  • Take particular care when driving on roads with loose surfaces or potholes.
  • These conditions may cause losses in tire inflation pressure, reducing the cushioning ability of the tires. In addition, driving on rough roads may cause damage to the tires themselves, as well as the vehicle’s wheels and body.
• Low profile tires (vehicles with 18 or 19-inch wheels)
  • Low-profile tires may cause greater damage than usual to the tire wheel when sustaining impact from the road surface. Therefore, pay attention to the following:
    • Be sure to use proper tire inflation pressure. If tires are under-inflated, they may be damaged more severely.
    • Avoid potholes, uneven pavement, curbs, and other road hazards. Failure to do so may lead to severe tire and wheel damage.
• If tire inflation pressure of each tire becomes low while driving Do not continue driving, or your tires and/or wheels may be ruined.

Tire inflation pressure

Tire inflation pressure

The recommended cold tire inflation pressure and tire size are displayed on the tire and loading information label. (P. 584)

Inspection and adjustment procedure

1. Tire valve
2. Tire pressure gauge

1. Remove the tire valve cap.
2. Press the tip of the tire pressure gauge onto the tire valve.
3. Read the pressure using the gauge gradations.
4. If the tire inflation pressure is not at the recommended level, adjust the pressure.
   1. If you add too much air, press the center of the valve to deflate.
5. After completing the tire inflation pressure measurement and adjustment, apply soapy water to the valve and check for leakage.
6. Put the tire valve cap back on.

Tire inflation pressure check interval

• You should check tire inflation pressure every two weeks, or at least once a month.
• Do not forget to check the spare.

Effects of incorrect tire inflation pressure

Driving with incorrect tire inflation pressure may result in the following:

• Reduced fuel economy
• Reduced driving comfort and poor handling
• Reduced tire life due to wear
• Reduced safety
• Damage to the drivetrain
  • If a tire needs frequent inflating, have it checked by your Toyota dealer.

Instructions for checking tire inflation pressure

When checking tire inflation pressure, observe the following:

• Check only when the tires are cold.
  • If your vehicle has been parked for at least 3 hours or has not been driven for more than 1 mile or 1.5 km, you will get an accurate cold tire inflation pressure reading.
• Always use a tire pressure gauge.
  • It is difficult to judge if a tire is properly inflated based only on its appearance.
• It is normal for the tire inflation pressure to be higher after driving as heat is generated in the tire. Do not reduce tire inflation pressure after driving.
• Never exceed the vehicle capacity weight.
  • Passengers and luggage weight should be placed so that the vehicle is balanced.

WARNING

• Proper inflation is critical to saving tire performance Keep your tires properly inflated.
  If the tires are not properly inflated, the following conditions may occur which could lead to an accident resulting in death or serious injury:
  • Excessive wear
  • Uneven wear
  • Poor handling
  • Possibility of blowouts resulting from overheated tires
  • Air leaking from between tire and wheel
  • Wheel deformation and/or tire damage
  • Greater possibility of tire damage while driving (due to road hazards, expansion joints, sharp edges on the road, etc.)

NOTICE

When inspecting and adjusting tire inflation pressure Be sure to put the tire valve caps back on. If a valve cap is not installed, dirt or moisture may get into the valve and cause an air leak, resulting in decreased tire inflation pressure.

Wheels

If a wheel is bent, cracked or heavily corroded, it should be replaced. Otherwise, the tire may separate from the wheel or cause a loss of handling control.

Wheel selection

When replacing wheels, care should be taken to ensure that they are equivalent to those removed in load capacity, diameter, rim width, and inset*. Replacement wheels are available at your Toyota dealer. Conventionally referred to as “offset”. Toyota does not recommend using the following:

• Wheels of different sizes or types
• Used wheels
• Bent wheels that have been straightened

Aluminum wheel precautions (if equipped)

• Use only Toyota wheel nuts and wrenches designed for use with your aluminum wheels.
• When rotating, repairing, or changing your tires, check that the wheel nuts are still tight after driving 1000 miles (1600 km).
• Be careful not to damage the aluminum wheels when using tire chains.
• Use only Toyota genuine balance weights or equivalent and a plastic or rubber hammer when balancing your wheels.

When replacing wheels

• The wheels of your vehicle are equipped with a tire pressure warning valve and transmitters that allow the tire pressure warning system to provide advance warning in the event of a loss in tire inflation pressure.
• Whenever wheels are replaced, tire pressure warning valves and transmitters must be installed. (P. 475)

WARNING

• When replacing wheels
  • Do not use wheels that are a different size from those recommended in the Owner’s Manual, as this may result in a loss of handling control.
  • Never use an inner tube in a leaking wheel that is designed for a tubeless tire. Doing so may result in an accident, causing death or serious injury.
• When installing the wheel nuts
  • Be sure to install the wheel nuts with the tapered ends facing inward. ( P. 553) Installing the nuts with the tapered ends facing outward can cause the wheel to break and eventually cause the wheel to come off while driving, which could lead to an accident resulting in death or serious injury.
  • Never use oil or grease on the wheel bolts or wheel nuts. Oil and grease may cause the wheel nuts to be excessively tightened, leading to bolt or disc wheel damage. In addition, the oil or grease can cause the wheel nuts to loosen and the wheel may fall off, causing an accident and resulting in death or serious injury. Remove any oil or grease from the wheel bolts or wheel nuts.

NOTICE

• Replacing tire pressure warning valve and transmitters
  • Because tire repair or replacement may affect the tire pressure warning valve and transmitters, make sure to have tires serviced by your Toyota dealer or another qualified service shop. In addition, make sure to purchase your tire pressure warning valve and transmitters at your Toyota dealer.
  • Ensure that only genuine Toyota wheels are used on your vehicle. The Tire pressure warning valve and transmitters may not work properly with non-genuine wheels.

Air conditioning filter

The air conditioning filter must be changed regularly to maintain air conditioning efficiency.

Removal method

• Turn the engine switch off.
• Open the glove box and remove the glove box cover inside the glove box.
• Remove the filter cover.
  • Unlock the filter cover.
  • Move the filter cover in the direction of the arrow, and then pull it out of the claws.
• Remove the filter case.
  • There may be foreign objects on top of the air conditioning filter.
• Remove the air conditioning filter from the filter case and replace it with a new one. The “UP” marks shown on the filter and the filter case should be pointing up.

Checking interval

Inspect and replace the air conditioning filter according to the maintenance schedule. In dusty areas or areas with heavy traffic flow, early replacement may be required. (For scheduled maintenance information, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.)

If air flow from the vents decreases dramatically

The filter may be clogged. Check the filter and replace if necessary.

Air conditioning filter with deodorizing function

• When fragrances are placed in your vehicle, the deodorizing effect may become significantly weakened in a short period.
• When an air conditioning odor comes out continuously, replace the air conditioning filter.

NOTICE

• When using the air conditioning system
  • Make sure that a filter is always installed.
  • Using the air conditioning system without a filter may cause damage to the system.
• To prevent damage to the filter cover
  • When moving the filter cover in the direction of the arrow to release the fitting, pay attention not to apply excessive force to the claws. Otherwise, the claws may be damaged.

Wireless remote control/electronic key battery

Replace the battery with a new one if it is depleted.

You will need the following items

• Flathead screwdriver
• Small flathead screwdriver
• Lithium battery CR2032

Replacing the battery

Vehicles without a smart key system

• Remove the key cover.
  • To prevent damage to the key, cover the tip of the flathead screwdriver with a rag.
• Remove the battery cover.
  • If the battery cover is difficult to remove, lift the edge to remove it.
• Remove the depleted battery using a small flathead screwdriver.
  • Insert a new battery with the “+” terminal facing up.
• Install the battery cover with the
  • tab facing up.
  • Push the entire edge of the battery cover into the key.
• Install the key cover.
  • Align the key cover with the key and then press it straight into the key.
  • Make sure that the key cover is securely installed without any gaps between it and the key.
• Operate the or switch and check that the doors can be locked/unlocked.

Vehicles with a smart key system

• Release the lock and remove the mechanical key.
• Remove the key cover.
  • To prevent damage to the key, cover the tip of the flathead screwdriver with a rag.
• Remove the depleted battery using a small flathead screwdriver.
  • When removing the cover, the electronic key module may stick to the cover and the battery may not be visible. In this case, remove the electronic key module in order to remove the battery.
  • Insert a new battery with the “+” terminal facing up.
• When installing the key cover and mechanical key, install by conducting and with the directions reversed.
• Operate the or switch and check that the doors can be locked/unlocked

When replacing the key battery

Be careful not to lose the battery or any other small parts.

Use a CR2032 lithium battery

• Batteries can be purchased at your Toyota dealer, local electrical appliance shops, or camera stores.
• Replace only with the same or equivalent type recommended by the manufacturer.
• Dispose of used batteries according to local laws.

If the key battery is depleted

The following symptoms may occur:

• The smart key system (if equipped) and wireless remote control will not function properly.
• The operational range will be reduced.

WARNING

• Battery precautions Observe the following precautions. Failure to do so may result in death or serious injury.
  • Do not swallow the battery. Doing so may cause chemical burns.
  • Vehicles without a smart key system: A coin battery or button battery is used in the key. If a battery is swallowed, it may cause severe chemical burns in as little as 2 hours and may result in death or serious injury.
  • Vehicles with a smart key system: A coin battery or button battery is used in the electronic key. If a battery is swallowed, it may cause severe chemical burns in as little as 2 hours and may result in death or serious injury.
  • Keep away new and removed batteries from children.
  • Vehicles without a smart key system: If the cover cannot be firmly closed, stop using the key and stow the key in a place where children cannot reach it, and then contact your Toyota dealer.
  • Vehicles with a smart key system: If the cover cannot be firmly closed, stop using the electronic key and stow the key in a place where children cannot reach it, and then contact your Toyota dealer.
  • If you accidentally swallow a battery or put a battery into a part of your body, get emergency medical attention immediately.

WARNING

• To prevent battery explosion or leakage of flammable liquid or gas
  • Replace the battery with a new battery of the same type. If the wrong type of battery is used, it may explode.
  • Do not expose batteries to extremely low pressure due to high altitude or extremely high temperatures.
  • Do not burn, break or cut a battery.

NOTICE

1. For normal operation after replacing the battery
   Observe the following precautions to prevent accidents:
   1. Always work with dry hands.
      1. Moisture may cause the battery to rust.
   2. Do not touch or move any other component inside the remote control.
   3. Do not bend either of the battery terminals.
2. When removing the battery cover (vehicles without a smart key system)
   1. Do not forcibly remove the battery cover, otherwise, it may be damaged.
   2. If the battery cover is difficult to remove, lift the edge to remove it.

Checking and replacing fuses

If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary.

1. Turn the engine switch off.
2. Open the fuse box cover.
   1. Engine compartment (type A)
   2. Engine compartment (type B)(if equipped)
   3. Under the driver’s side instrument panel
3. Make sure to push the claw when removing/installing the lid.
4. Remove the fuse with the pull-out tool.
   1. Only type A fuses can be removed using the pullout tool.
5. Check if the fuse is blown.
   1. Type A
   2. Type B
   3. Type C

• Normal fuse
• Blown fuse
  • Replace the blown fuse with a new fuse of an appropriate amperage rating. The amperage rating can be found on the fuse box lid.

After a fuse is replaced

● If the lights do not turn on even after the fuse has been replaced, a bulb may need replacement. (P. 502)
● If the replaced fuse blows again, have the vehicle inspected by your Toyota dealer.

If there is an overload in a circuit

The fuses are designed to blow, protecting the wiring harness from damage.

WARNING

• To prevent system breakdowns and vehicle fires Observe the following precautions.
  Failure to do so may cause damage to the vehicle, and possibly a fire or injury.
  • Never use a fuse of a higher amperage rating than that indicated, or use any other object in place of a fuse.
  • Always use a genuine Toyota fuse or equivalent.
    • Never replace a fuse with a wire, even as a temporary fix.
  • Do not modify the fuses or fuse boxes.

NOTICE

Before replacing fuses Have the cause of electrical overload determined and repaired by your Toyota dealer as soon as possible.

Light bulbs

You may replace the following bulbs yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer. For more information about replacing other light bulbs, contact your Toyota dealer.

Preparing for light bulb replacement

• Check the wattage of the light bulb to be replaced. (P. 589)

Bulb locations

• Front
  • Front turn signal/parking lights (bulb type)
  • Front side marker lights (bulb type)
• Rear
  • Back-up lights (bulb type)
  • Rear turn signal lights (bulb type)
  • Rear side marker lights (bulb type)

Replacing light bulbs

Front turn signal/parking lights (bulb type)

1. Turn the bulb base counterclockwise.
2. Remove the light bulb.
3. Install a new light bulb and then install the bulb base to the light unit by inserting it and turning it clockwise.

Front side marker lights (bulb type)

1. To ensure enough space to perform work, turn the steering wheel to move the front wheel away from the light bulb to be replaced.
   1. Turn the steering wheel to the left when replacing the right side light bulb, and turn the steering wheel to the right when replacing the left side light bulb.
2. Remove the fender liner clips.
3. To protect the front bumper from being damaged, apply protective tape around the clip as shown in the illustration.
   1. Use masking tape, etc. Do not use duct tape, as it may leave residue or damage the paint when removed.
4. Insert a small flathead screwdriver between the front bumper and fender liner at the position marked with and then separate the front bumper from the fender liner.
   1. To separate the front bumper from the fender liner, pry up the fender liner while pulling the front bumper outward as shown in the illustration.
5. Pull back the fender liner and turn the bulb base counterclockwise.
6. Remove the light bulb.
7. Install a new light bulb and then install the bulb base to the light unit by inserting it and turning it clockwise.
8. Return the fender liner to its original position, and install the clips.
   1. Make sure that the fender liner is correctly positioned on the inner side of the front bumper.
9. To Install the fender liner to the front bumper, engage the clip to the front bumper.
10. Remove the protective tape.

Back-up lights (bulb type)

1. Open the trunk lid and remove the clips.
2. .Partly remove the trunk lid cover.
3. Disconnect the connector while depressing the lock release. (When replacing right side bulb only.)
4. Turn the bulb base counterclockwise.
5. Remove the light bulb.
6. Install a new light bulb and then install the bulb base to the light unit by inserting it and turning it clockwise.
7. Connect the connector.(When replacing right side bulb only.)
8. Reinstall the trunk lid cover with the clips.

Rear turn signal lights (bulb type) and rear side marker lights (bulb type)

1. Open the trunk and apply protective tape to the vehicle body around the light unit.
   1. Use masking tape, etc. Do not use duct tape, as it may leave residue or damage the paint when removed.
2. Remove the cover.
   1. Insert a flathead screwdriver between the cover and the light unit and pry up the cover in several positions as shown in the illustration to disengage the claws (indicated by a dotted line).
   2. Pull the cover toward the rear of the vehicle to disengage the claws (indicated by a dotted line) and remove the cover.
   3. To prevent scratching the vehicle, wrap the tip of the flathead screwdriver with a cloth, etc.
3. Remove the 2 bolts.
4. Remove the light unit.
   1. Attach a long piece of packing tape to the light unit and fold the excess in half.
   2. Hold the folded portion and pull it toward the rear of the vehicle to remove the light unit.
5. Turn the bulb base counterclockwise.
   1. Rear turn signal lights
   2. Rear side marker lights
6. Remove the light bulb.
   1. Rear turn signal lights
   2. Rear side marker lights
7. Install a new light bulb and then install the bulb base to the light unit by inserting it and turning it clockwise.
   1. Rear turn signal lights
   2. Rear side marker lights
8. Install the light unit.
   1. Align the tabs and push the light unit toward the front of the vehicle to install it.
9. Install the 2 bolts.
10. Install the cover.
11. Remove the protective tape.

Replacing the following bulbs

If any of the lights listed below has burnt out, have it replaced by your Toyota dealer.

• Headlights
• Daytime running lights
• Parking lights (LED type)
• Front turn signal lights (LED type)
• Front side marker lights (LED type)
• Side turn signal lights (if equipped)
• Taillights
• Rear side marker lights (LED type)
• Stoplights
• Rear turn signal lights (LED type)
• Back-up lights (LED type)
• High mounted stoplight
• License plate lights

LED light bulbs

The lights other than the front turn signal/parking lights (bulb type), front side marker lights (bulb type), back-up lights (bulb type), rear turn signal lights (bulb type) and rear side marker lights (bulb type) consist of a number of LEDs. If any of the LEDs burn out, take your vehicle to your Toyota dealer to have the light replaced.

Condensation build-up on the inside of the lens

Temporary condensation build-up on the inside of the headlight lens does not indicate a malfunction. Contact your Toyota dealer for more information in the following situations:

• Large drops of water have built up on the inside of the lens.
• Water has built up inside the headlight.

WARNING

• Replacing light bulbs
  • Turn off the lights. Do not attempt to replace the bulb immediately after turning off the lights.
    • The bulbs become very hot and may cause burns.
  • Do not touch the glass portion of the light bulb with bare hands. When it is unavoidable to hold the glass portion, use and hold with a clean dry cloth to avoid getting moisture and oils on the bulb.
    • Also, if the bulb is scratched or dropped, it may blow out or crack.
  • Fully install light bulbs and any parts used to secure them. Failure to do so may result in heat damage, fire, or water entering the headlight unit. This may damage the headlights or cause condensation to build upon the lens.
• To prevent damage or fire
  • Make sure bulbs are fully seated and locked.