2021 Tesla Model 3 Parts and Accessories Owners Manual

2021 Tesla S logo

2021 Tesla Model 3 Parts and Accessories

2021 Tesla Model 3

Parts, Accessories, and Modifications

Use only genuine Tesla parts and accessories. Tesla performs rigorous testing on parts to ensure their suitability, safety, and reliability. Purchase these parts from Tesla, where they are professionally installed and where you can receive expert advice about modifications to Model 3. Accessories are available for purchase from Tesla stores or online at www.tesla.com.

Note
Some accessories may not be available in your market region.

Tesla is unable to assess parts manufactured by other distributors and therefore accepts no responsibility if you use non-Tesla parts on Model 3.

Warning
Installing non-approved parts and accessories, or performing non-approved modifications, can affect the performance of Model 3 and the safety of its occupants. Any damage caused by using or installing non-approved parts, or by performing non-approved modifications, is not covered by the warranty.
Warning
Tesla does not accept liability for death, personal injury or damage that occurs if you use or install non-approved accessories or make non-approved modifications.

Accessory Wheels and Tires

If your Model 3 is fitted with Tesla accessory wheels or tires, the Gross Axle Weight Rating (GAWR), wheel, tire, and loading information may be different from the labels shown on the vehicle. Refer to the relevant following section for updated information.

Note
If your vehicle is not fitted with Tesla accessory wheels or tires (it is fitted with the factory original wheels and tires, including Tesla genuine replacement parts), refer to the labels attached to the center door pillar for the most accurate information for your Model 3.

20″ Sport Wheels

 
Wheels Location Width (in) Offset (mm)
20″ Front/Rear 8.5 40
 
Tires (front/rear) Size Tire Pressure
Michelin, Pilot Sport 4S (PS4S) 235/35ZR20 42 PSI (290 kPa)*
*Increase the tire pressure to 44 PSI (300 kPa) prior to driving 136 mph (220 kph) or faster.
 
GAWR
Front 2407 lbs 1,092 kg
Rear 2,767 lbs 1,255 kg

19″ Sport Wheels

2021 Tesla Model 3 Parts and Accessories-2
 
Wheels Location Width (in) Offset (mm)
19″ Front/Rear 8.5 40
 
Tires (front/rear) Size Tire Pressure
Continental, ProContact RX 235/40R19 42 PSI (290 kPa)*
Hankook Ventus S1 Evo3 235/40R19 42 PSI (290 kPa)*
Pirelli Winter Sottozero 3 235/40R19 42 PSI (290 kPa)
*Increase the tire pressure to 44 PSI (300 kPa) prior to driving 134 mph (215 kph) or faster.
 
GAWR
Front 2,447 lbs 1,110 kg
Rear 2,767 lbs 1,255 kg

20″ Zero-G Wheels (Performance)

2021 Tesla Model 3 Parts and Accessories-3
 
Wheels Location Width (in) Offset (mm)
20″ Front/Rear 9 34
 
Tires (front/rear) Size Tire Pressure
Michelin, Pilot Sport 4S (PS4S) 235/35ZR20 42 PSI (290 kPa)
Michelin PS Cup 2 245/35ZR20 42 PSI (290 kPa)
 
GAWR
Front 2,650 lbs 1,202 kg
Rear 2,784 lbs 1,263 kg

20″ Zero-G Wheels (Non-Performance)

 
Wheels Location Width (in) Offset (mm)
20″ Front/Rear 9 40
 
Tires (front/rear) Size Tire Pressure
Michelin, Pilot Sport 4S (PS4S) 235/35ZR20 42 PSI (290 kPa)
 
GAWR
Front 2,650 lbs 1,202 kg
Rear 2,784 lbs 1,263 kg

19″ Gemini Wheels (Performance)

See Removing and Installing Aero Covers for information on how to remove and install Gemini wheel covers.

2021 Tesla Model 3 Parts and Accessories-4
 
Wheels Location Width (in) Offset (mm)
19″ Front/Rear 8.5 35
 
Tires (front/rear) Size Tire Pressure
Hankook Ventus S1 Evo3 235/40R19 42 PSI (290 kPa)*
Pirelli Winter, Sottozero 3 235/40R19 42 PSI (290 kPa)*
*Increase the tire pressure to 44 PSI (300 kPa) prior to driving 136 mph (220 kph) or faster.
 
GAWR
Front 2510 lbs 1,141 kg
Rear 3,023 lbs 1,374 kg

18″ Aero Wheels

2021 Tesla Model 3 Parts and Accessories-5
 
Wheels Location Width (in) Offset (mm)
18″ Front/Rear 8.5 40
 
Tires (front/rear) Size Tire Pressure
Michelin, Primacy MXM4 235/45R18 42 PSI (290 kPa)
Michelin, Pilot Sport 4 (PS4) 235/45R18 42 PSI (290 kPa)
Pirelli Winter Sottozero Serie II 235/45R18 42 PSI (290 kPa)
 
GAWR
Front 2,447 lbs 1,110 kg
Rear 2,840 lbs 1,288 kg

Body Repairs

If your Model 3 is in a collision, contact Tesla or a Tesla-approved Body Shop to ensure that it is repaired with genuine Tesla parts. Tesla has selected and approved body shops that meet strict requirements for training, equipment, quality, and customer satisfaction.

Some repair shops and insurance companies might suggest using non-original equipment or salvaged parts to save money. However, these parts do not meet Tesla’s high standards for quality, fit and corrosion resistance. In addition, non-original equipment and salvaged parts (and any damage or failures they might cause) are not covered by the warranty.

Using RFID Transponders

When attaching an RFID transponder (used by many automated toll systems) inside Model 3, place the transponder on the passenger side of the rear view mirror as shown. This ensures best results and minimizes any obstruction to your driving view.

Note
You can also attach a weather-proof transponder to the front license plate.
2021 Tesla Model 3 Parts and Accessories-6

Installing Front License Plate Bracket

To accommodate jurisdictions that require a license plate on the front of your vehicle, Model 3 is equipped with a license plate bracket. This bracket conforms to the shape of your vehicle’s front bumper and is adhered to it using strong adhesive.

Note
Tesla recommends performing this procedure on a clean, dry vehicle during a warm day. Cold and/or wet conditions may result in reduced performance of the adhesive.

To install the front license plate bracket:

Animation reflecting the steps to install the front license plate bracket.
  1. Get isopropyl alcohol and test it on a non-visible painted surface of your vehicle to confirm that it does not damage or remove the paint.
  2. Clean the mounting site with isopropyl alcohol and allow to dry for at least one minute.
  3. Fully remove the protective tape from the adhesive at the top of the bracket and partially remove the tape from the top of the adhesive on each side. Leave the bottom half of the tape on the sides in place and fold the unattached tape outward for easy removal after aligning the bracket to the bumper.
  4. While tilting the top of the license plate bracket away from the bumper (to prevent adhering it to the wrong location), align the bottom center of the license plate bracket with the middle of the grille as shown.
    Note
    Be as precise as possible when aligning the bracket because you will be unable to reposition it once adhered to the bumper.
  5. While correctly aligned, move the top of the bracket against the bumper and apply pressure so that it is held in place by the adhesive.
  6. Remove the remaining tape from the sides of the bracket then press the entire bracket firmly against the bumper, ensuring the bracket is held in place by all adhesive areas.
  7. Once the bracket is securely mounted, use the four supplied screws to attach your license plate to the bracket (tighten to 3 Nm/2.2 ft-lbs).

Leave a Comment