2021 Polestar 1 Cruise control Owners Manual

Adjusting set speed for driver support

It is possible to adjust set speeds for the cruise control, Adaptive Cruise Control* and Pilot Assist* functions.

1	+: Increases the set speed
2	-: Reduces the set speed
3	Set speed

Change a set speed by pressing the + (1) or – (2) buttons briefly or by pressing and holding them:
- Brief press: Each press changes the speed in +/- 5 km/h (+/- 5 mph) increments.
- Press and hold: Release the button when the set speed indicator (3) has moved to the desired speed.

> The most recently set speed will be stored.

NOTE

For vehicles without Adaptive Cruise Control*, speed instead increases by +/- 1km/h (+/- 1 mph) each time the button is pressed.

Using the accelerator pedal

If speed is increased by depressing the accelerator pedal while pressing the + (1) button on the steering wheel, the vehicle’s speed when the button is pressed will be stored as the set speed.

Temporarily increasing speed using the accelerator pedal, e.g. when passing another vehicle, will not affect the setting. The vehicle will return to the set speed when the accelerator pedal is released.

Possible speed

The lowest speed that can be set is 30 km/h (20 mph). When following another vehicle, ACC can monitor that vehicle’s speed and slow your own vehicle down to a standstill, but it is not possible to set speeds lower than 30 km/h (20 mph). The driver support functions can follow another vehicle at speeds from a standstill up to 200 km/h (125 mph). Pilot Assist can provide steering assistance from near-stationary speeds up to 140 km/h (87 mph).

Function buttons and symbols

	: Activates Cruise Control from standby mode and resumes the set speed
	: Increases the set speed
	: From standby mode – activates Cruise Control and sets the current speed
	: From active mode – deactivates/puts Cruise Control in standby mode
	: Reduces the set speed
	Marker for set speed
	The vehicle’s current speed
	Set speed

NOTE

In vehicles equipped with Adaptive Cruise Control*(ACC), it is possible to switch between Cruise Control and Adaptive Cruise Control.

WARNING

The function is supplementary driver support intended to facilitate driving and help make it safer – it cannot handle all situations in all traffic, weather and road conditions.
The driver is advised to read all sections in the Manual about this function to learn of its limitations, which the driver must be aware of before using the function.
Driver support functions are not a substitute for the driver’s attention and judgment. The driver is always responsible for ensuring the vehicle is driven in a safe manner, at the appropriate speed, with an appropriate distance to other vehicles, and in accordance with current traffic rules and regulations.

Using engine braking instead of applying the brakes

Cruise Control regulates speed by lightly applying the brakes. On downgrades, it can sometimes be desirable to roll a bit faster and let speed be reduced instead by engine braking alone. The driver can temporarily disengage the Cruise Control braking function.

To disengage CC:

Press the accelerator pedal about halfway down and then release it.

> Cruise Control will automatically disengage the automatic brake function and speed will only be reduced using the engine braking function.

Cruise control standby mode

Cruise control (CC) (Cruise Control) can be deactivated and put in standby mode. This may happen automatically or be due to driver intervention. Standby mode means that the function is selected in the instrument panel but not activated. In standby mode, cruise control will not regulate speed.

Standby mode due to action by the driver

Cruise control will be deactivated and put in standby mode if any of the following occurs:

The brakes are applied.
The gear selector is moved to N.
The vehicle is driven faster than the set speed for more than 1 minute.

The driver must then control the vehicle’s speed.

Automatic standby mode

Adaptive Cruise Control may go into standby mode if e.g.:

The wheels lose traction.
The engine speed (rpm) is too low/high.
The temperature in the brake system becomes too high.
The vehicle’s speed goes below 30 km/h (20 mph).

The driver must then control the vehicle’s speed.s

Deactivating cruise control

Cruise control (CC)(Cruise Control) can be turned off.

Press the button on the steering wheel (2).

> The symbol and indicators are extinguished – cruise control is set in standby mode.

Press the (1) or (3) buttons on the steering wheel to select another function.

> The cruise control symbol and marking (4) in the instrument panel will go out and the set/stored maximum speed will be erased.

Selecting and activating cruise control

The Cruise Control (CC)(Cruise Control) function must be selected and activated in order to regulate speed.

In order to start Cruise Control from standby mode, the vehicle’s current speed must be 30 km/h (20 mph) or higher.

Press the (1) or (3) button on the steering wheel keypad and scroll to the cruise control symbol (4).

> Gray symbol – cruise control is in standby mode.

When cruise control is selected, press (2) on the steering wheel keypad to activate it.

> White symbol – cruise control starts and the current speed is stored as the maximum speed. The lowest speed that can be set is 30 km/h (20 mph).

Reactivating cruise control to the last stored speed

When cruise control is selected, press on the steering wheel keypad to activate it.

> The Cruise Control marking in the instrument panel will change from GRAY to WHITE and the vehicle will then return to the most recently set speed.

WARNING

A noticeable increase in speed may follow when the speed is resumed with the steering wheel button.

Switching between cruise control and Adaptive Cruise Control* in the center display

When the regular cruise control (CC) is selected in the instrument panel, you can switch to Adaptive Cruise Control (ACC) in the center display’s Function view.

Activate or deactivate the function using this button in the center display’s Function view.

Illuminated button indicator light – Adaptive Cruise Control is deactivated and the regular cruise control is in standby mode.
Extinguished button indicator light – regular cruise control is deactivated and the Adaptive Cruise Control is in standby mode.

A symbol in the instrument panel indicates which cruise control system is active
Cruise control (CC)	Adaptive Cruise Control (ACC)

2021 Polestar 1 Cruise control Owners Manual