If children are carried in the rear seats, the isolator switch should be used to prevent the operation of the windows. If the windows are operated by young children, there is a risk of serious injury or death.
Make sure that you remove the smart key when leaving the vehicle. This will prevent unsupervised operation of the windows and sunroof, which may result in an injury.
Wherever possible, remove any snow, ice, dirt, leaves, etc., from the panoramic roof mechanism before closing. Failure to do so may damage the panoramic roof mechanism.
To prevent accidental damage, make sure that any roof rack load will not interfere with the opening of the panoramic roof.
To open a window: Press lightly at the front of the switch and release.
To close a window: Pull up lightly at the front of the switch and release.
For one-touch open and close operation, press or pull firmly at the front of the switch and release.
The windows will operate for 5 minutes after the engine is switched off, as long as none of the doors are opened.
To open the blind: Press lightly at the rear of the switch and release.
To close the blind: Press lightly at the front of the switch and release.
For one-touch open and close operation, press firmly at the front or rear of the switch and release.
Long Wheel Base (LWB) vehicles, fitted with standard rear seats, feature an additional roof blind switch. The switch is located on the rear face of the center console.
Press lightly at the rear of the switch to tilt the roof. Once tilted, lightly press again to open the roof.
From the fully open position, press lightly at the front of the switch to close to the tilt position, then press lightly again to close fully.
For one-touch open and close operation, press firmly at the front or rear of the switch and release.
The panoramic roof blind can be controlled via the button located on the rear door panels.
Press the button to open the roof blind. Press the button for a second time to close the roof blind.
The rear door panel’s roof blind button triggers an opening movement unless the blind is fully open.
Pressing the button during the opening movement causes the roof blind to close. When the movement is initiated from the front overhead console, the rear buttons have no effect until the movement stops. For information on isolating the rear windows, refer to child safety locks. See the Linked procedure not present at the moment.
The automatic operation of the roof blind can be adjusted via the climate settings screen on the touchscreen display. When the feature is selected and the doors are locked, the roof blind closes automatically. When the engine is running, the roof blind returns to the previous open position.
Before operating the side window blinds, make sure that no objects or parts of the body are in a position to obstruct its operation. Failure to do so may result in damage to the operating mechanism.
Before operating the side window blinds, it is important to note the following:
The side window blinds will operate for 5 minutes after the engine has been switched off, provided the windows are fully closed.
Closing a window or roof blind onto any part of the body can result in serious injury.
Before closing a window or the panoramic roof, make sure that no occupants have any part of their body in a position where it could be trapped. Even with an anti-trap system, death or serious injury could occur.
The anti-trap mechanism does not operate when closing the panoramic roof from the tilted position. The panoramic roof can cause serious injury should a body part become trapped. Always make sure that the panoramic roof is free from obstructions before closing.
Anti-trap protection will stop window or panoramic roof movement if an obstruction or resistance is detected. Check the window or panoramic roof and its aperture, and remove any obstructions (e.g., ice, etc.).
If it is still necessary to raise the window or close the panoramic roof, the override procedure is as follows:
If this procedure fails to remove the blockage, the window operation may need to be reset. See WINDOW RESET.
The panoramic roof’s anti-trap mechanism works differently and does not require a reset if activated. See PANORAMIC ROOF RESET.
The solar attenuating glass windshield filters sunlight passing through a special laminated layer. Electronic devices, such as toll road payment tags or Radio Frequency (RF) ID tags, can be attached at the indicated locations. The locations are on the inside of the windshield. If the tags are located at any other part of a solar attenuating windshield, the electronic scanners may not recognize them. The optimal fixing location is at the top of the windshield, as shown in (1), close to the interior rear-view mirror.
The electronic device should be in the size-appropriate location on the driver’s side of the windshield.
Transponders, mounted on the front license mount plinth, can be used as an alternative, dependent on the market and availability.
Access the comprehensive 2010-2018 VW Jetta Passenger Fuse Box Diagram to troubleshoot electrical issues effectively.…
Explore the comprehensive VW Jetta Passenger Fuse Box Diagram to troubleshoot electrical issues effectively. Understand…
Under Hood Fuse Box Location Remove the front luggage compartment cover. Under Hood Fuse Box…
2022 Kawasaki NINJA H2 SX SE Brake Lever Adjuster Owner's Manual NOTICE Only adjust the front…
2023 Land Rover Range Rover Evoque Exiting The Vehicle SINGLE LOCKING WARNING Before exiting the…
2023 Land Rover Range Rover Evoque Front Seats FRONT SEAT SAFETY Make sure to read…