2022 Land Rover Range Rover Load Carrying
LOAD CARRYING
Never allow passengers to travel in the loadspace under any circumstances. All vehicle occupants should be seated correctly and should wear a seat belt at all times when the vehicle is in motion. Failure to do so can lead to serious injury or death in the event of an accident.
All items carried in the vehicle should be properly secured. If the vehicle is involved in an accident or subject to sudden braking or a change of direction, loose items can cause serious injury.
LOADSPACE COVER
Medical devices: The undersides of the front and mid-loadspace cover sections each contain a magnet. The magnets are located in the recesses along the center line of the vehicle. The magnetic field may interfere with pacemakers, defibrillators, or other medical devices. When in the vehicle, or when handling the loadspace cover, maintain at least 6 inches (15 cm) of separation between your pacemaker or defibrillator and the loadspace cover.
Never place objects on top of the loadspace cover. During an accident or sudden maneuver, loose objects can cause serious injury or death.
Do not store the loadspace cover lose in the vehicle. During an accident or sudden maneuver, loose objects could cause serious injury or death.
To fold the loadspace cover
- Push firmly down and forward. Then push upward on the underside of the loadspace cover handle.
- Fold the loadspace cover forward.
To remove or refit the loadspace cover, it is first necessary to make sure the rear seats are in the fully upright position.
To remove the loadspace cover:
- Pull the whole assembly rearward to disconnect the locating pins. Remove and store safely.
- To refit the loadspace cover, place the assembly in position. Engage the locating pins into the sockets and press firmly to lock the assembly in position. If required, pull the outer edge towards the rear, to cover the loadspace area.
To access the loadspace from inside the vehicle: Push firmly down on the furthest edge of the cover while pulling it toward the rear seats. The cover folds, allowing access to the loadspace area.
To access objects in the loadspace from within the vehicle, it may first be necessary to remove the rear head restraints.
To fold the loadspace cover:
- Flip over the first board of the loadspace cover.
- Fold the remaining boards.
To remove or refit the loadspace cover, it is first necessary to make sure the rear seats are in the fully upright position.
To remove the loadspace cover:
- Disconnect the two locating pins.
- Pull the whole assembly rearward. Remove and store safely.
To refit the loadspace cover, place the assembly in position. Engage the locating pins into the sockets and press firmly to lock the assembly in position. If required, pull the outer edge towards the rear to cover the loadspace area.
DEPLOYABLE LOADSPACE FLOOR
The deployable loadspace floor is operated by the buttons on the right side of the load compartment.
To operate the deployable loadspace floor:
- Press and hold the button to move the deployable loadspace floor backward.
- Press and hold the button to move the deployable loadspace floor forward.
The deployable loadspace floor can be raised. To raise the deployable loadspace floor:
- Briefly, press button (1) to move the deployable loadspace floor backward.
- Lift the deployable loadspace floor by the rear edge.
Support struts hold the deployable loadspace floor in the open position.
Make sure that power cables are disconnected from the high-voltage power socket before raising the deployable loadspace floor. Power cables may become trapped. Death or serious injury could occur.
Make sure that the high voltage power socket flap is in the fully closed position before raising the deployable loadspace floor. Failure to do so could cause damage to the vehicle.
LUGGAGE ANCHOR POINTS
All items carried in the loadspace area should be properly secured. If the vehicle is involved in an accident, subject to sudden braking or a change of direction, loose items can cause serious injury.
- To assist in safely securing large items of luggage, four lashing eyes are located on the loadspace floor.
- If adjustable lashing eyes are fitted, first turn the locking switch counter-clockwise to unlock. Press the locking switch and slide to the required position in the luggage rail. Release the locking switch to latch it into position. Move the lashing eye slightly until a click is heard. The lashing eye is now secured. Turn the button clockwise to lock.
A range of approved luggage retention accessories is available from a retailer/authorized repairer.
To assist in safely securing large items of luggage, six lashing eyes are located on the loadspace floor.
LUGGAGE DIVIDER
A luggage divider kit is provided, to assist with safely securing items of luggage to the loadspace floor.
Floor-mounted luggage rails provide a full-width mounting channel. The channel accommodates a flexible retracting band and/or a solid telescopic divider, to secure soft and hard luggage of all shapes and sizes.
- Press, then pull the retracting band until the required length is reached.
NOTES
Only use the retracting band along the side of the loadspace floor, as illustrated.
- Adjust the divider to the required length.
- Unlock the appropriate lashing eye. Attach the retracting band and divider.
- With the lashing eye in the unlocked position, press the mechanism and slide to the required position in the luggage rail.
- Lock the lashing eye in the required position.
- To remove the retracting band and divider from the lashing eye, unlock the lashing eye and press the lock or unlock button to release.
SKI HATCH
The ski hatch, located on the backrest, can be used for transporting long objects.
To open the ski hatch:
- Release and lower the rear seat armrest.
- Press the center release button and fold down the ski hatch panel.
To close the ski hatch panel, push the panel up to the closed position.
SKI HATCH FOR EXECUTIVE CLASS VEHICLES:
To open the ski hatch:
- Press the button with the ski hatch symbol. The button is part of the seat fold control panel in the loadspace.
- The rear seat armrest and the ski hatch fold down.
To close the ski hatch, push the ski hatch panel up to the closed position. The ski hatch locks automatically.