Do not operate the windshield wipers on a dry windshield, as it may inhibit the operation of the wipers.
In freezing or very hot conditions, use the winter park position to allow the wiper blades to be lifted from the windshield should they become stuck. See WINTER PARK POSITION.
Remove any snow, ice, or frost from the windshield, around the wiper arms and blades, and from the cowl area before operating the wipers.
To avoid damage to the wiper blade, do not lift the wiper by the wiper blade. Always lift the wiper by the wiper arm.
Make sure the wipers are not in automatic rain-sensing mode and are switched off before entering a car wash. If the wipers operate during the car washing process, damage may occur to the wiper mechanism.
The windshield is no longer wiped effectively and the automatic rain-sensing function degrades if the wipers become worn. Always replace worn or damaged wiper blades as soon as possible.
If the wiper blades become stuck or jammed, an electronic cut-out temporarily halts the wiper’s operation. If this happens, switch off the wipers and vehicle ignition, when safe to do so. Clear any obstructions and free the wiper blades before attempting to switch on the ignition.
The front wipers do not operate while the hood is open.
When reversing (R) gear is selected and the front wipers are operating, the rear wiper activates.
The rear wiper does not operate while the tailgate is open.
Drip wipe on the windshield can be enabled or disabled by a retailer/authorized repairer.
Rear wiper road speed-related frequency can be enabled or disabled by a retailer/authorized repairer.
If the wipers leave smears on the glass after the car has been washed, this may be due to wax or other residues. Should this occur, clean the glass with the recommended windshield washer fluid. See LUBRICANTS AND FLUIDS. The service position moves the wipers to allow wiper blade replacement. See WIPERS SERVICE POSITION.
Static droplets may not be detected on initial start-up. A single wipe should be used to clear the windshield.
In dry and often sunny conditions, optical influences and dirt accumulation on the windshield may result in the windshield wipers activating inadvertently. To prevent this, it is recommended that, under these conditions, the wash/wipe control is returned to the OFF position. See WIPER OPERATION. The rain sensor is mounted on the inside of the windshield, behind the rear-view mirror. The sensor is able to detect the presence and amount of water on the windshield and automatically activates the windshield wipers accordingly. To activate the rain-sensitive wipers, move the wash/wipe control to the AUTO position (1). The behavior of the system may be tailored to the driver’s preference by rotating the collar (2).
If the wash/wipe control is turned to the AUTO position (1), the wipers do not operate if either front door is open. The rain sensor feature can be enabled or disabled in the instrument panel menu. See INSTRUMENT PANEL MENU.
If the vehicle’s speed drops below 5 mph (8 km/h) with the wipers operating, the wipers switch to the next lowest speed. When the vehicle’s speed increases to over 5 mph (8 km/h), the original wiper speed setting is restored automatically.
The feature can be enabled or disabled by a retailer/authorized repairer.
The frequency of the rear wiper, when set to intermittent, increases with the vehicle’s speed.
The feature can be enabled or disabled by a retailer/authorized repairer.
Make sure that the wiper arms are in the winter park position before lifting the wiper blades away from the windshield. Failure to do so may result in damage to the hood. When the vehicle is parked, the wipers can be set to park in a higher position than normal. The wiper blades can be lifted from the windshield to limit the possibility of the blades sticking to the glass. Lifting the wiper blades from the windshield aids in the removal of snow, mud, leaves, etc. The wiper’s winter park position can be enabled or disabled via the Vehicle Settings menu in the instrument panel. See INSTRUMENT PANEL MENU.
The wipers move to the winter park position when the ignition is switched off. The wipers remain in the winter park position until one of the following occurs:
Access the comprehensive 2010-2018 VW Jetta Passenger Fuse Box Diagram to troubleshoot electrical issues effectively.…
Explore the comprehensive VW Jetta Passenger Fuse Box Diagram to troubleshoot electrical issues effectively. Understand…
Under Hood Fuse Box Location Remove the front luggage compartment cover. Under Hood Fuse Box…
2022 Kawasaki NINJA H2 SX SE Brake Lever Adjuster Owner's Manual NOTICE Only adjust the front…
2023 Land Rover Range Rover Evoque Exiting The Vehicle SINGLE LOCKING WARNING Before exiting the…
2023 Land Rover Range Rover Evoque Front Seats FRONT SEAT SAFETY Make sure to read…