2023 Land Rover Range Rover Evoque Windows
ELECTRIC WINDOWS
Make sure you remove the smart key when leaving the vehicle. Removing the smart key from the vehicle prevents unsupervised operation of the windows, which may result in an injury.
To operate the windows:
- Window switches: Briefly pull a switch fully up, and release to close a window.Briefly press a switch fully down, and release to fully open a window. Pressing or pulling a switch again stops window movement. The windows operate for 5 minutes after the engine is switched off, as long as none of the doors are opened.
Rear windows have a short drop feature for passenger comfort. The first press of a switch lowers the window a short distance to give a flow of air. A second press lowers the window to its full extent.
If a resonance or booming sound occurs when a rear window is open, lowering an adjacent front window by approximately 1 inch (25 mm) eliminates the condition.
- Rear window and door isolator switch: Press the switch to isolate operation of the rear windows and doors. The indicator light in the switch illuminates to confirm isolation.
WARNING
If children are carried in the rear seats, the isolator switch should be used to prevent operation of the windows and doors. If the windows or doors are operated by young children there is a risk of serious injury or death.
- Sunroof:
NOTES
The front and rear of the switch has a two-stage operation. Lightly press and hold to manually operate to the required position. Alternatively, press fully and release for one-touch operation. One-touch operation can be halted, at any time, by pressing the switch again.
With the sunroof closed, press the rear of the switch to partially or fully raise the sunroof to the tilt position. Press the rear of the switch again to partially or fully open the sunroof.
NOTESIf the sunroof blind is closed, the sunroof switch also opens the sunroof blind while operating the sunroof.
With the sunroof open, press the front of the switch to partially or fully close the sunroof.
CAUTIONTo prevent accidental damage, make sure any roof rack load does not interfere with the opening of the sunroof.
- Sunroof blind:The sunroof blind can be opened whenever required, but it can only be closed when the sunroof is closed. If the sunroof is partially closed, the sunroof blind only partially closes to the same position.
NOTES
The front and rear of the switch has a two-stage operation. Lightly press and hold to manually operate to the required position. Alternatively, press fully and release for one-touch operation. One-touch operation can be halted, at any time, by pressing the switch again.
Press the rear of the switch to partially or fully open.
Press the front of the switch to partially or fully close.
ANTI-TRAP PROTECTION
Closing a window or roof blind onto any part of the body can result in serious injury.
Before closing a window or the roof blind, make sure no occupants have any part of their body in a position where it could be trapped. Even with an anti-trap system, death or serious injury could occur.
Anti-trap protection is designed to stop window or roof blind movement if an obstruction or resistance is detected. Check the window or roof blind, and its aperture, and remove any obstructions, e.g., ice, etc.
If it is still necessary to raise the window, the override procedure is as follows:
- Attempt to close the window. Anti-trap prevents closure and lowers the window slightly.
- Within 10 seconds, attempt to raise the window again. Anti-trap prevents closure and lowers the window slightly.
- Attempt to close the window for a third time, this time hold the switch in the close position. The window raises while the switch is held. Hold until closed.
If this procedure fails to remove the blockage, or if the windows do not operate correctly, the window’s operation may need to be reset. See WINDOW RESET.
ROOF BLIND
Roof blind open and close switch:
To open the blind, press the rear of the switch to the second position and release. The blind fully opens. A further press stops movement of the blind.
Alternatively, press the rear of the switch to the first position and hold until the blind reaches the desired position. Release the switch.
To close the blind, press the front of the switch to the second position and release. The blind fully closes. A further press stops movement of the blind.
Alternatively, press the front of the switch to the first position and hold until the blind reaches the desired position. Release the switch.
ROOF BLIND ANTI-TRAP MECHANISM
Before closing the roof blind, make sure that no occupants have any body part in a position where it could be trapped. Even with an anti-trap system, death or serious injury could occur.
To prevent serious personal injury or damage to the vehicle, the roof blind has an anti-trap mechanism. If the roof blind encounters a resistance when closing, it stops. Dependent on the roof blind’s current position, the roof blind partially or fully opens to allow the removal of any obstruction. Press and hold the front of the switch, within 10 seconds of the partial or full opening, to override the anti-trap mechanism.
If the roof blind fails to operate correctly, it may need to be reset. See PANORAMIC ROOF BLIND RESET.
SUNROOF ANTI-TRAP MECHANISM
Before closing a window, the sunroof, or the roof blind, make sure that no occupants have any body part in a position where it could be trapped. Even with an anti-trap system, death or serious injury could occur.
The anti-trap mechanism does not operate when closing the sunroof from the tilted position. The sunroof can cause serious injury should a body part become trapped. Always make sure that the sunroof is free from obstructions before closing.
To prevent serious personal injury or damage to the vehicle, the sunroof and roof blind have an anti-trap mechanism. If the sunroof or the roof blind encounters a resistance when closing, it stops. Dependent on the sunroof’s or the roof blind’s current position, the sunroof or the roof blind partially or fully opens to allow the removal of any obstruction. Press and hold the front of the switch, within 10 seconds of the partial or full opening, to override the anti-trap mechanism.
If the sunroof or the roof blind fails to operate correctly, it may need to be reset. See SUNROOF RESET.
SOLAR ATTENUATING GLASS
The solar attenuating glass windshield filters sunlight passing through a special laminated layer.
Electronic actuating cards, such as toll road payment cards or Radio Frequency (RF) ID tags, can be fixed at dedicated locations. The locations are on the inside of the windshield. If the cards are located at any other part of a solar attenuating windshield, the electronic scanners may not recognize them.
The optimal fixing location is at the top of the windshield, as shown at (1), close to the interior rear-view mirror.
The electronic actuating card should be in the size-appropriate location on the driver’s side of the windshield.
Transponders, mounted on the front license plate plinth, can be used as an alternative, dependent on the market and availability.