Make sure the following warnings have been read and fully understood before using the navigation system.
Failure to use the navigation system safely could result in an accident, leading to serious injury or death.
The navigation system is not a substitute for driving safely with due care and attention. Road Traffic Regulations must always be observed. Drivers should not assume that a feature will correct errors in judgment when driving.
The driver is responsible for staying alert, driving safely, and for being in control of the vehicle at all times, relative to the prevailing conditions. The driver is responsible for determining the safety of the route suggested by the navigation system. The navigation system may not function properly in all circumstances.
Make sure the relevant safety warnings and cautions have been read and understood before operating the touchscreen. See TOUCHSCREEN SAFETY.
During any map update, the vehicle’s electrical system must not be switched off, before the update is complete. Doing so cancels the map update and potentially leaves the system without any available map data. See MAP UPDATES.
The speed camera notifications are not available in certain markets.
The speed camera notifications can be enabled or disabled via the navigation settings menu. See NAVIGATION SETTINGS .
The navigation system guides the driver to a selected destination using map and turn information displayed on the touchscreen, instrument panel, and in the Head-Up Display (HUD). Navigation instructions can also be complemented by voice guidance.
The touchscreen is used to control the navigation system via menus and map displays. See USING THE NAVIGATION SYSTEM.
The navigation system uses a selection of Pivi Pro features to enhance the navigation system. See PIVI PRO FEATURES.
The vehicle’s instrument panel can be set up to display navigation instructions and maps. See INSTRUMENT PANEL VIEW.
The HUD can also be set up to display turn instructions. See HEAD-UP DISPLAY (HUD).
The navigation system can also be controlled via voice commands. See NAVIGATION VOICE CONTROL .
Under certain conditions, it is possible for the vehicle’s position displayed on the map screen to be incorrect. Incorrect vehicle positioning may happen when:
GPS signals may occasionally be interrupted due to physical barriers, such as roads under raised highways and tunnels.
Make sure the relevant safety warnings have been read and understood before operating the navigation system. See NAVIGATION SAFETY .
The touchscreen home menu displays a navigation tile. See TOUCHSCREEN HOME MENU.
Depending if a route has been set or not, the navigation tile may display differently.
The following navigation tile displays when no route is set:
The following navigation tile displays when a route is set:
Traffic: Displays traffic information when a route is set.
Internet connection is required to receive traffic information. See CONNECTIVITY OVERVIEW.
Rest areas: Displays a list of rest areas during the set route guidance, should the user choose to stop.
Fuel stations: Displays a list of fuel stations in order of distance during an active route guidance.
Make sure the relevant safety warnings have been read and understood before operating the navigation system. See NAVIGATION SAFETY .
To access the navigation system, touch the navigation icon via the navigation tile on the home screen. See TOUCHSCREEN HOME MENU.
Alternatively, touch the navigation icon via the driver side bar. See DRIVER SIDE BAR ICONS.
The navigation tile displays various shortcuts depending if a route has been set or not. See NAVIGATION TILES.
A first time user should set up personal preferences in the navigation settings menu. Personal preferences may include settings for managing which selected routing mode and route preferences are applied. See NAVIGATION SETTINGS .
Touch the navigation icon to display a map view of the current vehicle position and search card.
Zoom icons only display after navigation map interaction.
The map zoom setting can be altered by using a pinch or push motion. The map view can be panned using a swipe motion.
Make sure the relevant safety warnings have been read and understood before operating the navigation system. See NAVIGATION SAFETY .
To set a destination:
Input the required destination.
From the suggestion list located at the bottom of the keyboard, select the required destination.
To search for Points of Interest (POIs) from the category list:
EAT & DRINK.
FUEL STATIONS.
PARKING.
CAR DEALER/REPAIRER.
SHOPPING.
SIGHTS & MUSEUM.
LEISURE & OUTDOORS.
GOING OUT.
ACCOMMODATION.
POLICE/EMERGENCY.
HOSPITAL or HEALTHCARE FACILITY.
More options may be available.
To edit the route:
Touch the drop-down icon³, suggestions icon⁴, or the OK soft key, to view the search results. Touch the text box to continue typing.
The navigation system calculates all routes, based on the selected routing mode and route preferences. See NAVIGATION SETTINGS .
An address, place name, or category can be added as a waypoint after a destination has been selected. See EDIT ROUTE.
Search icon.¹
Route preferences icon.²
Drop-down icon.³
Suggestions icon.⁴
Make sure the relevant safety warnings have been read and understood before operating the navigation system. See NAVIGATION SAFETY .
When a route has been selected, depending on the navigation settings, the touchscreen displays a turn by turn guidance map.
The information panel can be edited to display other options. See NAVIGATION SETTINGS .
Make sure the relevant safety warnings have been read and understood before operating the navigation system. See NAVIGATION SAFETY .
When a route is selected, the user has the option to edit the route via the following:
A waypoint can also be added, deleted, or a route rearranged for any active route guidance.
To add a waypoint:
Input the required destination and select.
Alternatively, select a waypoint from any saved destinations or categories.
If the selected destination is correct, touch the Add soft key.
Follow the same process if any additional waypoints are required.
The following options can also be selected:
Trash can icon.¹
Make sure the relevant safety warnings have been read and understood before operating the navigation system. See NAVIGATION SAFETY .
A range of notifications can be displayed via the navigation map screen, e.g., low fuel, safety cameras, traffic information, and maneuver details.
All navigation notifications can be edited via the navigation settings menu. See NAVIGATION SETTINGS .
Make sure the relevant safety warnings have been read and understood before operating the navigation system. See NAVIGATION SAFETY .
Detailed information about an address, place name, or category, can be saved as a favorite.
To add a favorite destination, touch the favorite icon¹. The saved destination is added to a list of saved favorites.
The list of favorites is located via the SAVED category, in the search box, on the navigation map screen. See USING THE NAVIGATION SYSTEM.
To remove a saved favorite, touch the favorite icon¹.
If no route is selected, select the required favorite to set it as a destination. If a route is selected, select the required favorite to add it as a waypoint.
Favorite icon.¹
Make sure the relevant safety warnings have been read and understood before operating the navigation system. See NAVIGATION SAFETY .
To view the navigation settings menu:
The following options are available for the user to enable or disable:
Depending on the vehicle specification and the market availability, not all navigation setting options will be available.
Map:
Display a realistic 3D city model, when available.
Traffic flow will not be displayed on the map when this setting is selected.
Airport
Amusement Park
ATM
Car Rental
Car Repair
Expo Center
Education
Fuel Station
Government Office
Hospital
Hotel
Library
Movie Theater
Museum
Outdoor sport
Parking
Pharmacy
Police
Post Office
Religious Place
Rest Area
Restaurants
Safety Cameras
Shops
Theater
Tourist Attraction
Tourist Information.
Route and Guidance:
Enables traffic aware routing for all routes.
Fastest.
Shortest.
ECO.
Avoid Routes Unsuitable for Caravans and Trailers.
Avoid Car Sharing Lanes.
Avoid Congestion Charges.
Avoid Ferries.
Avoid Highways.
Avoid Monorail.
Avoid Toll Roads.
Avoid Tunnels.
Avoid Unpaved Roads.
Avoid roads requiring a vignette.
Shows Junction Views and Intersection Maps.
Learn My Routes: Help’s make day-to-day driving to go more smoothly by taking into account the current situation on routes the driver does regularly: Touch toggle to switch on or off.
Auto-start commute: Touch toggle to switch on or off.
‘Learn my routes’ improves day-to-day driving by assessing current conditions on routes you drive regularly.
Smart voice guidance: Touch toggle to switch on or off.
Enjoy a bit more peace and quiet when you’re driving in places you already know well.
Commute Suggestions: Touch ON or OFF to select.
Auto-Start Commute: Touch toggle to switch on or off.
Recognizes frequent destinations and automatically starts ‘My Commute’.
Delete Driving History: Touch to delete stored driving history.
Alerts:
Off
Chime
On.
Off
Visual Only
On.
About:
Map is up to date: Displays the date of the last map update.
Map Version: Displays the current map version.
New Map Available: Displays the map update URL.
Make sure the relevant safety warnings have been read and understood before operating the navigation system. See NAVIGATION SAFETY .
When auto-zoom is enabled, the map automatically zooms in when the vehicle is traveling at slow speeds and zooms out when traveling at higher speeds.
Auto-zoom can be enabled and disabled via the navigation settings menu. See NAVIGATION SETTINGS .
To adjust the volume of the navigation voice guidance, rotate the media system’s volume control while spoken guidance is given. See MEDIA CONTROLS.
The volume of the safety camera notification is linked to the voice guidance volume.
Make sure the relevant safety warnings have been read and understood before operating the navigation system. See NAVIGATION SAFETY .
The availability and functionality of navigation maps displayed on the instrument panel depends on the specification of the vehicle.
The instrument panel can be set up to show a view of a full navigation map or a mini navigation map, depending in the instrument panel setup.
In this view, essential information, e.g., vehicle speed, fuel level, and range is displayed as an information bar.
Navigation turn instructions are also available to the user and are displayed in the instrument panel and Head-Up Display (HUD).
Navigation turn instructions are only displayed if route guidance is active.
To display navigation map views in the instrument panel or HUD, please refer to the relevant section of the Owner’s Handbook. See CONFIGURING A VIRTUAL INSTRUMENT PANEL.
The instrument panel can be edited by the user to display alternative intersection and lane assistance map views. See NAVIGATION SETTINGS .
Make sure the relevant safety warnings have been read and understood before operating the navigation system. See NAVIGATION SAFETY .
Navigation voice control is not available in all markets.
When using voice control for the navigation system, information is used from the on-board navigation database. Online features are not available.
The user can command the navigation system to:
The navigate to a zip code voice command is not available in all markets.
For assistance when operating the navigation system’s voice control feature, please refer to the relevant section of the Owner’s Handbook. See VOICE TUTORIAL.
Make sure the relevant safety warnings have been read and understood before operating the navigation system. See NAVIGATION SAFETY .
For user safety, the vehicle must be stationary for an online or USB update process to avoid any distraction.
The map data in the navigation system is automatically updated via an online update. The user is only prompted with a notification when the update was successfully updated.
Online updates are only available if connected to the internet. See CONNECTIVITY OVERVIEW.
For further information on navigation system updates, please contact a retailer/authorized repairer.
The map data in the navigation system can also be updated by downloading the updated map data to a USB memory device.
Due to the map data file size, it is recommended that a USB 3.0 memory device is used to update the map data.
To update the navigation system’s map data using a USB, please visit: www.landrover.com and search for ‘Map Updates’.
To download to a USB memory device:
Information on the installed maps is available in the navigation settings menu. See NAVIGATION SETTINGS .
For further information on the navigation system, please visit: www.landrover.com.
Make sure the relevant safety warnings have been read and understood before operating the navigation system. See NAVIGATION SAFETY .
In order to benefit from the full range of Pivi Pro features, the vehicle requires a connection to the internet. See CONNECTIVITY OVERVIEW.
Pivi Pro uses a selection of features to enhance the navigation system.
Pivi Pro features include:
Make sure the relevant safety warnings have been read and understood before operating the navigation system. See NAVIGATION SAFETY .
Uses live traffic data feeds, allowing for better traffic information, planning, and rerouting, for the user to complete the journey more efficiently.
Historical and internet traffic information is not available in all markets.
Traffic information is displayed as color coded on the navigation map. The color codes are:
Real-time traffic can be displayed with a route selected or with no route selected.
In some instances, the real time traffic information feature does not operate if the navigation map displays 3D buildings.
Real-time traffic information does not automatically reroute journeys.
A traffic-enabled route can be selected. A traffic-enabled route displays improved and updated routes to the destination, avoiding traffic congestion and delays. An option can also be enabled to possibly find a route to the destination, avoiding an alerted incident or traffic flow issues.
A live internet connection is required to receive updated traffic information during the journey. See CONNECTIVITY OVERVIEW.
Make sure the relevant safety warnings have been read and understood before operating the navigation system. See NAVIGATION SAFETY .
While on route to a destination, the navigation system monitors live traffic conditions and takes into account typical traffic patterns for that time of day, keeping the user on the optimum route.
Online routing can be used in conjunction with commute mode.
Make sure the relevant safety warnings have been read and understood before operating the navigation system. See NAVIGATION SAFETY .
Before starting a route, the user can use the Route Planner smartphone app to set a destination. The smartphone app sends the selected destination automatically to the vehicle’s navigation screen.
Once parked, the Route Planner smartphone app guides the user to the selected destination, which includes public transport options.
The Route Planner smartphone app is only available in selected markets.
Downloading and installing the Route Planner smartphone app:
To sign in to the Route Planner smartphone app, use the same email address and password used to set up the InControl account. See INCONTROL ACCOUNT SET UP.
Apple® and iPhone® are registered trademarks of Apple Inc., registered in the US and other countries. App Store® is a service mark of Apple Inc.
Google™, Android™, and Google Play™ store is a registered trademark of Google LLC.
Make sure the relevant safety warnings have been read and understood before operating the navigation system. See NAVIGATION SAFETY .
The satellite views feature provides an overhead map view of the vehicle’s surroundings.
If the satellite view feature is used continuously, it may consume large amounts of mobile data. Check the data allowance is appropriately configured for providing high-data services.
Make sure the relevant safety warnings have been read and understood before operating the navigation system. See NAVIGATION SAFETY .
When a fuel station is selected during a Points Of Interest (POI) search, the nearby fuel stations can be sorted according to the price of the fuel. Fuel prices are updated to the vehicle’s database from the internet.
Fuel pricing information may not be updated in real time and cannot be guaranteed to be accurate.
In some markets, a relative price index is displayed instead of live fuel prices.
Make sure the relevant safety warnings have been read and understood before operating the navigation system. See NAVIGATION SAFETY .
Commute mode allows for the navigation system to learn regular commutes and automatically advises the user of the expected journey time based on live and historical traffic movements without the user having to input a destination.
The navigation system learns the routes the user takes for a set destination and advises which of those is the quickest.
Commute mode can be enabled and disabled via the navigation settings menu. See NAVIGATION SETTINGS .
Commute mode displays a highlighted route on the navigation map and uses the learned routes, combined with live traffic information, to calculate the fastest of the previously used routes.
If more than one commute is available, the alternative commutes become available for selection.
When the commute mode feature detects areas the driver regularly uses, the frequency of smart voice guidance reduces. See NAVIGATION SETTINGS .
Make sure the relevant safety warnings have been read and understood before operating the navigation system. See NAVIGATION SAFETY .
As the user approaches a destination, the navigation system displays available parking. Simply tap on the preferred car park. The navigation system updates to direct the user to it. Available parking and pricing information is also displayed for selected markets.
Make sure the relevant safety warnings have been read and understood before operating the navigation system. See NAVIGATION SAFETY .
The safety cameras feature provides the location of potential accident black spots, or areas that have been identified as a potential danger by the presence of safety cameras. Available in selected locations only.
Safety camera information is not available in all countries.
Access the comprehensive 2010-2018 VW Jetta Passenger Fuse Box Diagram to troubleshoot electrical issues effectively.…
Explore the comprehensive VW Jetta Passenger Fuse Box Diagram to troubleshoot electrical issues effectively. Understand…
Under Hood Fuse Box Location Remove the front luggage compartment cover. Under Hood Fuse Box…
2022 Kawasaki NINJA H2 SX SE Brake Lever Adjuster Owner's Manual NOTICE Only adjust the front…
2023 Land Rover Range Rover Evoque Exiting The Vehicle SINGLE LOCKING WARNING Before exiting the…
2023 Land Rover Range Rover Evoque Front Seats FRONT SEAT SAFETY Make sure to read…