2022 Kawasaki Z400 ABS Meter Instruments
Meter Instruments
- Tachometer
- Left Meter Button
- Right Meter Button
- Multifunction Meter
- Tachometer Gauge
- Economical Riding Indicator
- Coolant Temperature Gauge
- Gear Position Indicator
- Speedometer
- Fuel Gauge
- Multifunction Display
- Odometer
- Trip Meter A/B
- Current Mileage/Average Mileage/Cruising
- Range
- Clock
When the ignition switch is turned on, all LCD functions are shown for a few seconds, then the multifunction meter turns to operational mode.
Indicators
- Left Turn Signal Indicator (Green)
- Warning Indicator (Red)
- Engine Warning Indicator (Yellow)
- High Beam Indicator (Blue)
- Fuel Level Warning Indicator
- Right Turn Signal Indicator (Green)
- Neutral Indicator (Green)
- ABS Indicator (Yellow)
- Battery Warning Indicator
- Coolant Temperature Warning Indicator
- Oil Pressure Warning Indicator
Indicator Initial Operation
When the ignition switch is turned on, all indicators go on/off as shown in the table. If any indicator does not operate as shown, have it checked by an authorized Kawasaki dealer.
- When ignition switch is turned on.
- After a few seconds
- When engine starts.
- Goes on.
- Goes off.
- goes off shorty after the motorcycle starts moving.
When Warning Indicators Go On or Blink
When warning indicators appear, there could be a problem with vehicle function. Follow actions in the table after stopping the vehicle in a safe place. The numbers in this column corresponds to reference numbers on page 46.
- After continuous riding on a rough road.
- When the engine is started with the stand raised and the transmission engaged, and the rear wheel turns.
- When accelerating so abruptly that the front wheel leaves the ground.
- When the ABS has been subjected to strong electrical interference.
- When tire pressure is abnormal. Adjust tire pressure.
- When a tire different in size from the standard size is being used. Replace with standard size.
- When the wheel is deformed. Replace the wheel.
Other Indicators
Speedometer/Tachometer
A. Tachometer
B. Tachometer Gauge
C. Red Zone
D. Speedometer
Speedometer
The speedometer is digital and can be set for km/h or mph. The unit setting can be changed according to local regulations. Make sure the unit setting (km/h or mph) is cor-
rectly displayed before riding. Refer to the Unit Setting in the Display Setting section.
Tachometer
The tachometer shows the engine speed in revolutions per minute (r/min, rpm).
NOTICE
Engine speed should not be allowed to enter the red zone; operation in the red zone will overstress the engine and may cause serious engine damage. When the ignition switch is turned on, the tachometer segment(s) momentarily go from the minimum to the maximum reading, then go back the minimum reading to check its operation. If the tachometer does not operate correctly, have it checked by an authorized Kawasaki dealer.
Coolant Temperature Gauge
The coolant temperature gauge indicates the temperature of the engine coolant by the number of segments displayed.
A. Segments
B. H (Hot)
C. C (Cold)
If the coolant temperature rises to above 1150C (2390F), all segments go on, and the warning indicator and coolant temperature warning indicator go on. This warns the operator that the coolant temperature is high.
A. Waming Indicator (Red)
B. Coolant Temperature Warning Indicator
NOTICE
Stop the engine if the warning indicator and coolant temperature warning indicator go on. Prolonged engine operation will result in severe engine damage from overheating.
Display Setting
Multifunction Display
WARNING
For safety, do not operate the meter buttons while riding the motorcycle.
Push the left meter button or right meter button to select the display modes. The display modes can be shifted in the following order.
NOTE
The multifunction display is displayed in the unit depending on the unit mode setting.
A. Left Meter Button
B. Right Meter Button
C. Flow when pushing left meter button
D. Flow when pushing right meter button
Odometer
The odometer shows the total distance. This meter cannot be reset.
NOTE
When the figures come to 999999, the display is stopped and locked.
Trip Meter
To reset the trip meter:
- Push the left meter button to select the trip meter A or B.
- Push the left meter button and hold it in until the display turns to 0.0.
NOTE
When the trip meter reaches 9999.9 while riding, the meter resets to 0.0 and continues counting.
Current Mileage
The current mileage display is renewed every 4 seconds.
NOTE
When the ignition switch is turned on, the numerical value shows “— —.—.” After a few seconds of riding the numerical value is displayed.
Average Mileage
This display shows the average fuel consumption from the reset. The average mileage display is renewed every 5 seconds.
To reset the average mileage: Push the right meter button and hold it in until the average mileage values resets to ”
NOTE
- When the battery is disconnected, the average mileage resets to “——.—. “
- After resetting the average mileage, the numerical value is not displayed until the vehicle has traveled 100 m (328 f).
Cruising Range
This display shows the cruising range by numerical value, and indicates the cruising range from the remaining fuel in the fuel tank. This cruising range display is renewed every 20 seconds.
NOTE
- The cruising range value is no longer shown if the fuel level gets too low after the fuel level warning indicator staffs blinking.
- To recover the cruising range value display add fuel to at least the level needed for the fuel level warning indicators to stop blinking. The cruising range may still be displayed with a low fuel level, but it will not be accurate until enough fuel is added to stop the fuel level warning indicator from blinking.
Clock
To adjust the clock:
- Push the right meter button to select the clock.
- Push the right meter button and hold it until both the hour and minute dis- plays blink.
- Push the right meter button and hold it until “12h” or “24h” is appeared on the display.
- Push the left meter button to select “12h” or “24h.”
- Push the right meter button to select the hour or minute digits.
- Push the left meter button to adjust the hour or minute digits.
- To finish the clock adjustment, push the left meter button when both the hour and minute digits blink.
A. Flow when pushing and holding right meter button
B. Flow when pushing right meter button
C. Flow when pushing left meter button
NOTE
When the battery is disconnected, the clock is reset to 1:00 (“24h” display: 13:00) and starts working again when the battery is connected.
Unit Setting
A. Units
- Display the odometer in the multi- function display.
- Push the right meter button while pushing the left meter button to select the meter display units. The display units can be shifted in the following order.
Tachometer Display Setting
The tachometer display can be select from three patterns. To select tachometer display:
- Push the left and right meter buttons and hold them until the tachometer gauge sweeps.
- Push the right meter button to select the tachometer display pattern.
A. Flow when pushing right meter button
To finish the selecting, push the left and right meter buttons and hold them a few seconds.
Features
Economical Riding Indicator
When riding the motorcycle efficiently, the economical riding indicator appears on the multifunction meter to indicate favorable fuel consumption. Monitoring the economical riding indicator can help the rider maximize fuel efficiency.
A. Economical Riding Indicator
WARNING
Failing to properly observe the road ahead increases the chance of an accident resulting in severe injury or death. Do not concentrate on the economical riding indicator by taking your eyes off the road; observe using peripheral vision.
Fuel Gauge
The fuel in the fuel tank is shown by the number of segments displayed.
A. Segments
B. F (Full)
C. E (Empty)
NOTE
- When the fuel tank is full, all the segments are displayed. As the fuel level in the tank goes down, the segments disappear one by one from F (full) to E (empty).
- When the fuel level warning indicator and bottom segment blink, refer to the “When Warning Indicators Go On or Blink” of Indicators in this chapter.
Gear Position Indicator
This display shows the corresponding gear position when the transmission is shifted. As the transmission is shifted, the corresponding gear position (1st 6th) is shown in this display. When the transmission is in neutral, “N” is displayed, and the neutral indicator goes on.
A. Gear Position Indicator
B. Neutral Indicator (Green)
NOTE
If the gear position display in the multifunction meter blinks “—, ” the transmission is not properly shifted to 1st. Be sure to shift the transmission.