Gear Position Indicator
KTRC Mode Indicator
Tachometer
Speedometer
Clock
Coolant Temperature/Outside Temperature Meter
Multifunction Display
- Odometer
- Trip Meter A/B
- Current Mileage
- Average Mileage
- Cruising Range
- Average Speed
- Total Time
- Battery Voltage
Service Indicator
Bluetooth@ Connection Indicator
Fuel Gauge
Economical Riding Indicator

Background Color Change
When the current mileage, cruising range or battery voltage is displayed on a multifunction display, pushing and holding the lower button or right meter button to invert the background color of the display screen.

Flow when pushing and holding the lower button or right meter button

NOTE
When the average mileage, average speed or total time is displayed on a multifunction display, pushing and holding right meter button resets item and the background color of the display screen does not invert.

Ambient Brightness Sensor
The brightness of the meter instrument is controlled automatically depending on the ambient brightness.

Meter Instrument Brightness Setting
The brightness of the meter instrument can be adjusted manually in three levels. Refer to Brightness in the Menu Mode section.

Indicators

Right Turn Signal Indicator (Green)
Neutral Indicator (Green)
KTRC Indicator (Yellow)
ABS Indicator (Yellow)
Oil Pressure Warning Indicator (Red)
Coolant Temperature Warning Indicator
Battery Warning Indicator (Red)
Fuel Level Warning Indicator
Engine Warning Indicator (Yellow)
High Beam Indicator (Blue)
Left Turn Signal Indicator (Green)

Indicator Initial Operation

When the ignition switch is turned on, all indicators go on/off as shown in the table. If any indicator does not operate as shown, have it checked by an authorized Kawasaki dealer.

When ignition switch is turned on.
After a few seconds
When engine starts.
Goes on.
Goes off.
goes off shorty after the motorcycle starts moving.

When Warning Indicators Go On or Blink
When warning indicators appear, there could be a problem with vehicle function. Follow actions in the table after stopping the vehicle in a safe place. The numbers in this column corresponds to reference numbers.

After continuous riding on a rough road.
When the engine is started with the stand raised and the transmission engaged, and the rear wheel turns.
When accelerating so abruptly that the front wheel leaves the ground.
When the ABS has been subjected to strong electrical interference.
When tire pressure is abnormal. Adjust tire pressure.
When a tire different in size from the standard size is being used. Replace with a standard size.
When the wheel is deformed. Replace the wheel.

When Warning Messages Display
When warning messages appear, there could be a problem with a vehicle function. Have them checked by an authorized Kawasaki dealer.

Other Indicators

Speedometer/Tachometer

A. Speedometer
B. Tachometer
C. Red Zone

Speedometer
The speedometer is digital and can be set for km/h or mph. The unit setting can be changed ac- cording to local regulations. Make sure the unit setting (km/h or mph) is correctly displayed before riding. Refer to the Menu Mode section.

Tachometer
The tachometer shows the engine speed in revolutions per minute (r/min, rpm)

NOTICE
Engine speed should not be allowed to enter the red zone; operation in the red zone will overstress the engine and may cause serious engine damage. The tachometer also serves as the shift-up indicator.

Features

Gear Position Indicator

The current gear position is shown. When the transmission is in neutral, “N” appears.

NOTE
If the transmission gears are not engaged properly, the gear position indicator disappears.The gear position indicator also serves as the shift-up indicator function.

Shift-up Indicator Function
The shift-up indicator function indicates the timing for the next upshift. From 500 r/min (rpm) before reaching the set engine speed, the gear position indicator changes color to orange, the tachometer and the gear position indicator starts blinking slowly. When the engine speed reaches the set value, the tachometer also changes color to orange, and the gear position indicator and the tachometer blink rapidly.

A. Tachometer (Change color to orange and blink)
B. Gear Position Indicator (Change color to orange and blink)

The shift-up indicator function can be selected on or off, and the set value can be adjusted.

Shift-up Indicator Function Setting
Refer to Vehicle Settings in the Menu Mode section.

Fuel Gauge

The fuel level in the fuel tank is shown by the number of segments displayed between E (empty) and F (full).

NOTE
When the fuel level warning indicator and segment(s) blink, refer to When Warning Indicators Go On or Blink in the Indicators section.

Coolant Temperature Meter

When the water temperature is not displayed, pushing and holding the upper button to display water temperature.This meter shows the engine coolant temperature. If the coolant temperature is below 400C (1040F), – -” is displayed. If the coolant temperature rises to above 1150C (2390F), the meter starts blinking and the warning indicator goes on. If the coolant temperature rises to 1200C (2480F) or more, “Hi” appears and starts blinking, the coolant temperature warning indicator continues to appear. This warns the operator that the coolant temperature is high.

A. Coolant Temperature Warning Indicator

Stop the engine and check the coolant level in the reserve tank after the engine cools down. If the amount of coolant is insufficient, add coolant to the reserve tank. If the coolant level is good, have the cooling system checked by an authorized Kawasaki dealer.

NOTICE
Stop the engine if the coolant temperature shows “Hi.” Prolonged engine operation will result in severe engine damage from overheating.

Outside Temperature Meter

The outside temperature around the vehicle is shown.

When the outside temperature is not displayed, push and hold the up- per button to display the outside temperature.

NOTE

The outside temperature can be displayed from -200C (-40F) to 600C (14009.
it may not be displayed correctly in this meter when the vehicle speed is 20 km/h (12 mph) or less, or the outside temperature sensor gets wet. The reading of the outside temperature meter does not increase when the speed is 20 km/h (12 mph) or less.

WARNING
If the outside temperature is 30C (37 OF) or below when the ignition key is turned on, the outside temperature meter changes to black text on an orange background or the “ICE” message appears to warn the operator that roads may be icy. Check the road surface and ride carefully.

NOTE

When the outside temperature meter is not displayed, the “ICE” warning message appears.

A. “ICE” Warning Message

Economical Riding Indicator

When riding the motorcycle efficiently, the economical riding indicator appears on the LCD to indicate favorable fuel consumption. Monitoring the economical riding indicator can help
the rider maximizes fuel efficiency,

WARNING

Failing to properly observe the road ahead increases the chance of an accident resulting in severe injury or death. Do not concentrate on the economical rid- ing indicator by taking your eyes off the road; observe using peripheral vision.

KTRC Mode Indicator

The current setting of the KTRC mode is shown. Refer to the Kawasaki Traction Control (KTRC) section in the HOW TO RIDE THE MOTORCYCLE chapter.

Bluetooth Connection Indicator

The Bluetooth icon appears when your smart device is connected to the vehicle. The telephone icon appears when a phone call is received by your smart device. The mail icon appears when an email or text message is received.

A. Telephone Icon
B. Mail Icon

How to Setup Bluetooth Connection

Refer to Bluetooth in the Menu Mode section.

Bluetooth Connectivity

This motorcycle can connect to the smart device via built-in Bluetooth wireless technology. Using the application “IDEOLOGY THE APP,” several data of your vehicle can be accessed, and several setting items can be adjusted. Refer to the application for details.

WARNING

For safety, do not use a smart device while riding the motorcycle.

NOTE

Some smart devices may not be compatible even if Bluetooth technology is available.
The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.

Service Indicator

A. Service Indicator
B. “SERVICE” Message
This motorcycle has three types of maintenance reminders; the standard Kawasaki maintenance schedule, the user the defined interval for oil, and the user de the fined interval for regular maintenance to assist you with the maintenance on your Kawasaki. When the date or distance reaches the set value, the service indicator and the message appear on the display screen every time the ignition switch is turned on. only the “SERVICE” message disappears after 30 seconds.

Maintenance Reminder Setting

Refer to Service in the Menu Mode section.

Control Buttons

The upper, lower, and “SEL” buttons on the left handlebar and left and right buttons on the meter are used to operate the various functions of the display screen.

A. Upper Button
B. “SEL” Button
C. Lower Button
D. Left Meter Button
E. Right Meter Button

Multifunction Display

Push the upper and lower button or the left and right meter buttons to select the item. The display items are switched in the following order.

[Item switched by the button or left meter button]

Odometer
Trip Meter A
Trip Meter B

[Item switched by the lower button or right meter button]

Current Mileage
Average Mileage
Cruising Range
Average Speed
Total Time
Battery Voltage
- Flow when pushing the upper button or left meter button
- Flow when pushing the lower button or the right meter button

Odometer

The odometer shows the total distance. This meter cannot be reset.

NOTE

When the figures come to 999999, the display is stopped and locked.

Trip Meter

The trip meter shows the distance traveled since it was reset.

NOTE

When the trip meter reaches 9999.9 while riding, the meter resets to 0.0 and continues counting.

How to Reset

Refer to the Multifunction Display Resetting section.

Current Mileage

This shows the instantaneous rate of fuel consumption. It is renewed every 4 seconds.

NOTE

When the ignition switch is turned on, the numerical value shows “— —.—.”

After a few seconds of riding the numerical value is displayed.

Average Mileage

This shows the average rate of fuel consumption since it was reset. It is renewed every 5 seconds.

How to Reset
Refer to the Multifunction Display Resetting section.

Cruising Range

This indicates the cruising range from the remaining fuel in the fuel tank. It is renewed every 20 seconds.

NOTE

When there is sufficient fuel, “(+)” appears next to the cruising range value.
The cruising range value is no longer shown if the fuel level gets too low after the fuel level warning indicator starts blinking.
To recover the cruising range display, add fuel to at least the level needed for the fuel level warning indicator to stop blinking. The cruising range

the value may still be displayed with a low fuel level, but it will not be accurate until enough fuel is added to stop the fuel level warning indicator from blinking.

Average Speed

This shows the average vehicle speed since it was reset.

How to Reset

Refer to the Multifunction Display Re-setting section.

Total Time

This shows the amount of time that has elapsed while the ignition switch is turned on.

NOTE

When the figures come to 99:59, the display is stopped and locked.

How to Reset

Refer to the Multifunction Display Re-setting section.

Battery Voltage

This shows the current battery voltage.

NOTE

The battery voltage is displayed in the 9.0 16.0 V range. If the display range is exceeded, the indication is fixed at the maximum or minimum value.
The battery voltage shown in this dis- play may differ from the numerical value measured by a volt meter.

Multifunction Display Resetting

The following multifunction display items can be reset.

Trip Meter AIB
Average Mileage
Average Speed
Total Time
Push the left or right meter button to display the items that can be reset.
Push the left or right meter button and hold it until resetting is done.
- Flow when pushing and holding the left meter button
- Flow when pushing and holding the right meter button

Menu Mode

The menu mode can set various functions of the vehicle.

NOTE

When the vehicle speed exceeds 5 km/h (3 mph), the menu mode can not be displayed.

How to Enter/Exit Menu Mode

Push and hold the left and right meter buttons to enter or exit.
- Flow when pushing and holding the left and right meter button

Basic Operations in Menu Mode

A. Move highlighted item or choose the item
B. Shift to the next screen (set) or go back to the previous screen (cancel)

Vehicle Settings

Shift Lamp: Turn the shift-up indicator function on or off

Enter the menu mode.
Highlight “Vehicle Settings” using the left-meter button.
Push the right meter button to shift to the next screen.Flow when pushing the right meter button
- Flow when pushing and holding the right meter button

Shift Lamp

This switches the shift-up indicator function on or off.
Highlight “Shift Lamp” using the left-meter button.
Push the right meter button to shift to the next screen.
Choose on or off using the left meter button.
Push the right meter button.
- Flow when pushing the right meter button

Engine Speed

This adjusts the timing at which the shift-up indicator function works.

NOTE

When the “Shift Lamp” setting is off, this item is grayed out.
Highlight “Engine Speed” using the left-meter button.
Push the right meter button to shift to the next screen.
Set the desired engine speed using the left-meter button.
Push the right meter button.
- Flow when pushing the right meter button

Display

Brightness: Adjust the backlight of Lights

Brightness

This adjusts the backlight brightness of the screen on three levels.
Enter the menu mode.
Highlight “Display” using the left-meter button.
Push the right meter button to shift to the next screen.
Adjust the setting using the left-meter button.
Push the right meter button.
- Flow when pushing the right meter button

Date and Clock

Date: Adjust the date
Clock: Adjust the clock
Format: Choose a date and time notation

Enter the menu mode.
Highlight “Date and Clock” using the left meter button.
Push the right meter button to shift to the next screen.
- Flow when pushing the right meter button
- Flow when pushing and holding the right meter button

Format (Date)

This switches the date format.
Highlight “Format” under “Date” using the left meter button.
Push the right meter button to shift to the next screen.
Choose the date format using the left meter button.
push the right meter button.
- Flow when pushing the right meter button

Date

Highlight “Date” using the left meter button.
Push the right meter button to shift to the next screen.
Adjust the date using the left meter button.
Push the right meter button.
- Flow when pushing the right meter button

Format (Clock)

This switches the time display.

Highlight “Format” under “Clock” using the left meter button.
Push the right meter button to shift to the next screen.
Choose the 12-hour clock or 24-hour clock using the left-meter button.
Push the right meter button.
- Flow when pushing the right meter button

Clock

Highlight “Clock” using the left-meter button.
Push the right meter button to shift to the next screen.
Adjust the clock using the left-meter button.
Push the right meter button.
- Flow when pushing the right meter button

Service

The screen 1 of 2

Kawasaki Service: Dealer destined interval for periodic maintenance (can be activated or deactivated by authorized Kawasaki dealer)
Oil Change: User-defined interval for an engine oil change (user can set distance and end date maintenance reminder)

Screen 2 of 2

Rider Setting: User-defined interval for maintenance (user can set distance maintenance reminder)
NOTE

The disabled item is grayed out.
The distance shown on the meter in- indicates the remaining distance to the maintenance reminder and will de- crease as the vehicle is operated.
The service item changes to orange when the scheduled date or distance is reached.
Enter the menu mode.
Highlight “Service” using the left meter button.
Push the right meter button to shift to the next screen.
- Flow when pushing the right meter button
- Flow when pushing and holding the right meter button

Oil Change
This switches the maintenance schedule notification on or off. The setting distance also can be adjusted.

Highlight “Oil Change” using the left meter button.
Push the right meter button to shift to the next screen.
Choose on or off using the left meter button.
Push the right meter button.
- Flow when pushing the right meter button
Highlight “In” under “Oil Change” using the left meter button.
Push the right meter button to shift to the next screen.
Set the desired distance using the left-meter button.
Push the right meter button.
- Flow when pushing the right meter button

NOTE

The settable distance is up to 12 000 km (7 500 miles).
The setting date cannot be changed manually. It sets to one year later automatically when turning on this function or changing the distance. When the current date is “2021.01.01,” it sets to “2022.01.01.”

Rider Setting

This allows the rider to set the distance for certain maintenance items.
Highlight “Rider Setting” using the left-meter button.
Push the right meter button to shift to the next screen.
Choose on or off using the left meter button.
Push the right meter button.
- Flow when pushing the right meter button
Highlight “In” under “Rider Setting” using the left meter button.
Push the right meter button to shift to the next screen.
Set the desired distance using the left-meter button.
Push the right meter button.
- Flow when pushing the right meter button

NOTE

The settable distance is up to 12 000 km (7 500 miles).

Bluetooth

Bluetooth: Turn Bluetooth wireless technology on or off Regulatory: Display the acquired certification mark

NOTE

To use the Bluetooth function, “RIDE- OLOGY THE APP” is necessary.
Enter the menu mode.
Highlight “Bluetooth” using the left-meter button.
Push the right meter button to shift to the next screen.
- Flow when pushing the right meter button
- Flow when pushing and holding the right meter button
Push the right meter button to shift to the next screen.
Choose on or off using the left meter button.
Push the right meter button. When selecting “On,” the motorcycle starts searching for the smart device.
Turn on the Bluetooth function of the smart device and launch the app.
- Flow when pushing the right meter button

NOTE

If the motorcycle detects the paired device, they connect automatically.

A. Connected Device Name

In the pairing setting menu of the app, select “VERSYS 650” and tap the connect button. The motorcycle displays the passkey (PIN) on the display screen.
Enter the passkey (PIN) into the unpaired device.

A. Pass Key (PIN)

NOTE

If the motorcycle does not detect the device, bring the device closer to the meter instruments.
Highlight “Pairing” using the left meter button.
Push the right meter button to shift to the next screen. Choose “Limited” using the left meter button.
Push the right meter button.
- Flow when pushing the right meter button

NOTE

Set the “Pairing” item to “Limited” except when pairing the smart device.

To pair with other smart devices

Enter the menu mode.
Highlight “Bluetooth” using the left-meter button.
Push the right meter button to shift to the next screen.Flow when pushing the right meter button
- Flow when pushing and holding the right meter button
Highlight “Pairing” using the left meter button.
Push the right meter button to shift to the next screen.
Choose “open” using the left meter button.
Push the right meter button. The motorcycle starts searching for the smart device.
Turn the Bluetooth function of the smart device and launch the app.
- Flow when pushing the right meter button
When the remaining time has appeared, in the pairing setting menu of the app, select “VERSYS 650” and tap the connect button. The motorcycle displays the passkey (PIN) on the display screen.
Enter the passkey (PIN) into the unpaired device.

A. Pass Key (PIN)

When the connection is completed, the name of the connected device is displayed.

A. Connected Device Name

NOTE

When pairing is done, using the right and left meter buttons return to the “Pairing” item to “Limited”.
- Flow when pushing the right meter button

Regulatory

Highlight “Regulatory” using the left meter button.
Push the right meter button to shift to the next screen.
Push the right meter button.

Units

Speed: Switch unit of speed between kph and mph
Fuel Mileage: Switch unit of fuel consumption
Temperature: Switch unit of temperature between oc and OF

Enter the menu mode.
Highlight “Units” using the left meter button.
Push the right meter button to shift to the next screen.
- Flow when pushing the right meter button
- Flow when pushing and holding the right meter button

Speed

This switches the unit of speed.

Highlight “Speed” using the left-meter button.
Push the right meter button to shift to the next screen.
Choose “km/h” or “mph” using the left meter button.
push the right meter button.
- Flow when pushing the right meter button

Fuel Mileage

This switches the unit of fuel consumption.
Highlight “Fuel Mileage” using the left meter button.
Push the right meter button to shift to the next screen.
Choose the unit using the left meter button. push the right meter button.
- Flow when pushing the right meter button

NOTE