NINJA H2 R

2022 Kawasaki NINJA H2 R Drive Chain Owners Manual

2022 Kawasaki NINJA H2 R Drive Chain

Drive Chain

Drive Chain Lubrication

Lubrication is necessary when the chain appears dry. Use a lubricant for sealed chains to prevent deterioration of chain seals. If the chain is especially dirty, clean it using a cleaner for sealed chains following the instructions supplied by the chain cleaner manufacturer.

  • Apply lubricant to the sides of the rollers so that it will penetrate the rollers and bushings. Apply lubricant to the seals so that the seals will be coated with lubricant. Wipe off any excess lubricant.
  • Wipe off any lubricant that gets on the tire surface.

Drive Chain Slack Inspection

  • Set the motorcycle up on its side stand.
  • Clean the chain if it is dirty, and lubricate it if it appears dry.
  • Rotate the rear wheel to find the position where the chain is tightest, and measure the maximum chain slack by pulling up and pushing down the chain midway between the engine sprocket and rear wheel sprocket.

A. Chain Slack

  • If the drive chain is too tight or too loose, adjust it so that the chain slack is within the standard value.
  • Drive Chain Slack
    • Standard: 30 35 mm (1.2- 1.4 in.)

Drive Chain Slack Adjustment

NOTE

  • lf a torque wrench is not available, this item should be serviced by an authorized Kawasaki dealer.
  • Remove the seat and the tool kit (see the Seat section in the GENERAL INFORMATION chapter).
  • Remove the hook wrench by removing the hook wrench mounting bolts.

A. Hook Wrench Mounting Bolts
B. Hook Wrench

  • Attach the adapter in the tool kit to the hook wrench.
    NOTE
  • The adapter of the hook wrench is in the tool kit bag.

A. Hook Wrench
B. Adapter

  • Loosen the bearing housing clamp bolts gradually and evenly.

A. Bearing Housing Clamp Bolts

  • Turn the chain adjuster until the drive chain has the correct amount of slack with the hook wrench.
  • If the chain is too loose, turn the chain adjuster counterclockwise
  • If the chain is too tight, turn the chain adjuster clockwise.

A Chain Adjuster
B. Hook Wrench
C. Clockwise (direction to lose)

  • Confirm that there is no clearance between the chain adjuster and the swingarm. If there is a clearance, push the wheel to the right side of the vehicle to eliminate the clearance.

A. Chain Adjuster
B. Swingarm
C. No Clearance

  • Tighten the bearing housing clamp bolts to the specified torque following the tightening sequence.

Tightening Sequence:

  • Bearing Housing Clamp Bolts:
    • 33 (3.4 kgf•m, 24 ft•lb)

WARNING

A loose clamp bolt can lead to an accident resulting in serious injury or death. Tighten the clamp bolts to the proper torque.

  • Install the hook wrench in the original place, and tighten its bolts.
  • Check the rear brake (see the Brakes section in this chapter).
Automotive Solutions

Recent Posts

VW Jetta Engine Fuse Box Diagram

Access the comprehensive 2010-2018 VW Jetta Passenger Fuse Box Diagram to troubleshoot electrical issues effectively.…

7 months ago

VW Jetta Passenger Fuse Box Diagram

Explore the comprehensive VW Jetta Passenger Fuse Box Diagram to troubleshoot electrical issues effectively. Understand…

7 months ago

2023 Ford F-150 Lightning Fuse Box Diagram

Under Hood Fuse Box Location Remove the front luggage compartment cover. Under Hood Fuse Box…

2 years ago

2022 Kawasaki NINJA H2 SX SE Brake Lever Adjuster Owner’s Manual

2022 Kawasaki NINJA H2 SX SE Brake Lever Adjuster Owner's Manual NOTICE Only adjust the front…

2 years ago

2023 Land Rover Range Rover Evoque Exiting The Vehicle Owners Manual

2023 Land Rover Range Rover Evoque Exiting The Vehicle SINGLE LOCKING WARNING Before exiting the…

2 years ago

2023 Land Rover Range Rover Evoque Front Seats Owners Manual

2023 Land Rover Range Rover Evoque Front Seats FRONT SEAT SAFETY Make sure to read…

2 years ago