When the ignition switch is turned on, all LCD functions are shown for a few seconds, then the multifunction meter turns to operational mode.
Indicators
When the ignition switch is turned on, all indicators go on/off as shown in the table. If any indicator does not operate as shown, have it checked by an autho- rized Kawasaki dealer.
When Warning Indicators Go On or Blink
When warning indicators appear, there could be a problem with vehicle function. Follow actions in the table after stopping the vehicle in a safe place. The numbers in this column corresponds to reference numbers on page 46.
Other Indicators
A. Tachometer
B. Speedometer
C. Red Zone
Speedometer
The speedometer is digital and can be set for km/h or mph. The unit setting can be changed according to local regulations. Make sure the unit setting (km/h or mph) is cor- rectly displayed before riding. Refer to the Unit Setting in the Di-play Setting section.
Tachometer
The tachometer shows the engine speed in revolutions per minute (r/min, rpm).
NOTICE
Engine speed should not be allowed to enter the red zone; operation in the red zone will overstress the engine and may cause serious engine damage.When the ignition switch is turned on, the tachometer needle momentar- ily sweeps from the minimum to the maximum reading, then back the mini- mum reading to check its operation. If the tachometer does not operate correctly, have it checked by an authorized Kawasaki dealer.
Coolant Temperature Gauge
The coolant temperature gauge indicates temperature of the engine coolant by the number of segments displayed.
A. Segments
B. H (Hot)
C. C (Cold)
If the coolant temperature rises to above 1150C (2390F), all segments go on, and the warning indicator and coolant temperature warning indicator go on. This warns the operator that the coolant temperature is high.
A. Warning Indicator (Red)
B. Coolant Temperature Warning Indicator
NOTICE
Stop the engine if the warning indicator and coolant temper- ature warning indicator go on. Prolonged engine operation will result in severe engine damage from overheating.
Multifunction Display
WARNING
For safety, do not operate the meter buttons while riding the motorcycle.
Push the upper meter button or lower meter button to select the display modes. The display modes can be shifted in the following order.
NOTE
The multifunction display is dis-played in the unit depending on the unit mode setting.
NOTE
When the trip meter reaches 9999.9 while riding, the meter resets to 0.0 and continues counting.
Current Mileage
The current mileage display is renewed every 4 seconds.
NOTE
When the ignition switch is turned on, the numerical value shows “— —.—.” After a few seconds of riding the numerical value is displayed.
Average Mileage
This display shows the average fuel consumption from the reset. The average mileage display is renewed every 5 seconds.
To reset the average mileage:
Push the lower meter button and hold it in until the average mileage values resets to —.”
NOTE
Cruising Range
This display shows the cruising range by numerical value, and indicates the cruising range from the remaining fuel in the fuel tank. This cruising range display is renewed every 20 seconds.
NOTE
Unit Setting
A. Units
To adjust the clock:
A. Flow when pushing and holding upper and lower meter buttons
B. Flow when pushing lower meter button
C. Flow when pushing upper meter button
D. Flow when pushing and holding lower meter button
NOTE
When the battery is disconnected, the clock is reset to 1:00 (“24h” display: 13:00) and starts working again when the battery is connected
Economical Riding Indicator
When riding the motorcycle efficiently, the economical riding indicator appears on the multifunction meter to indicate favorable fuel consumption. Monitoring the riding indicator can help the rider maximize fuel efficiency.
A. Economical Riding Indicator
WARNING
Failing to properly observe the road ahead increases the chance of an accident resulting in se- vere injury or death. Do not concentrate on the economical riding indicator by taking your eyes off the road; observe using peripheral vision.
Fuel Gauge
The fuel in the fuel tank is shown by the number of segments displayed.
A. Segments
B. F (Full)
C. E (Empty)
NOTE
Gear Position Indicator
This display shows the corresponding gear position when the transmisSion is shifted. As the transmission is shifted, the corresponding gear position (1st 6th) is shown in this display. When the transmission is in neutral, “N” is displayed, and the neutral indicator goes on.
A. Neutral Indicator (Green)
B. Gear Position Indicator
NOTE
If the gear position display in the multifunction meter blinks “-,” the transmission is not properly shifted to 1st. Be sure to shift the transmission.
Access the comprehensive 2010-2018 VW Jetta Passenger Fuse Box Diagram to troubleshoot electrical issues effectively.…
Explore the comprehensive VW Jetta Passenger Fuse Box Diagram to troubleshoot electrical issues effectively. Understand…
Under Hood Fuse Box Location Remove the front luggage compartment cover. Under Hood Fuse Box…
2022 Kawasaki NINJA H2 SX SE Brake Lever Adjuster Owner's Manual NOTICE Only adjust the front…
2023 Land Rover Range Rover Evoque Exiting The Vehicle SINGLE LOCKING WARNING Before exiting the…
2023 Land Rover Range Rover Evoque Front Seats FRONT SEAT SAFETY Make sure to read…