2022 Jeep Wrangler Folding Windshield User Manual

2022 Jeep Wrangler Folding Windshield

FOLDING WINDSHIELD

CAUTION

Lowering of the windshield is NOT recommended in vehicles equipped with a Power Sliding Top. Damage will occur to the top as well as the header seal.

• The fold-down windshield on your vehicle is a structural element that can provide some protection in some accidents. The windshield also provides some protection against weather, road debris and intrusion of small branches and other objects.
• Do not drive your vehicle on-road with the windshield down, as you lose the protection this structural element can provide.
• If required for certain off-road uses, the windshield can be folded down. However, the protection afforded by the windshield is then lost. If you fold down the windshield, drive slowly and cautiously. It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road wit  the windshield folded down.
• Raise the windshield as soon as the task that required its removal is completed and before you return to on-road driving. Both you and your passengers should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down.

WARNING

Carefully follow these warnings to help protect against personal injury:

• Do not drive your vehicle on-road with the windshield down.
• Do not drive your vehicle unless the windshield is securely fastened, either up or down.
• Eye protection, such as goggles, should be worn at all times when the windshield is down.
• Be sure that you carefully follow the instructions for raising the windshield. Make sure that the folding windshield, windshield wipers, sidebars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle. Failure to follow these instructions may prevent your vehicle from providing you and your passengers’ protection in some accidents.
• If you remove the doors, store them outside the vehicle. In the event of an accident, a loose door may cause personal injury.

LOWERING THE WINDSHIELD

1. Before completing the following steps:
   1. If your vehicle is equipped with a Soft Top, the top MUST be lowered, and the door rails must be removed prior to lowering the windshield.
   2. If your vehicle is equipped with a Hard Top, the Freedom Panels MUST be removed prior to lowering the windshield.
   3. Refer to the following instructions for more information:
      1. Soft Top Lowering Ú page 85
      2. Door Frame Ú page 106
      3. Freedom Top Panels Ú page 93
2. Manually remove the protective caps over the windshield wiper hex bolts.
   1. Hex Bolt Cover Installed
   2. Hex Bolt Cover Removed
3. Using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.
4. Move to the inside of the vehicle and lower both sun visors.
5. Using the provided #40 Torx head driver, remove the four Torx screws located along with the interior of the windshield.
   1. Outside Torx Screws
   2. Inside Torx Screws
      NOTE: Store all of the mounting bolts in their original threaded holes and tighten them for safekeeping.
6. Lower the windshield gently until it contacts the tie-down bumpers (if equipped).
   1. Washer Nozzle
   2. Bumper
   3. Tie-Down
7. Secure the windshield by passing a cinch strap through the tie-down on either side of the hood and on the windshield frame. Tighten the strap to secure the windshield in place.

CAUTION

Do Not Overtighten! Damage to the windshield could result.

Adaptive Cruise Control (ACC)/Forward Collision Warning (FCW) Sensor Protective Cover — If Equipped

Your vehicle may be equipped with a protective cover that is to be used whenever the windshield is folded down in order to protect the Adaptive Cruise Control (ACC)/Forward Collision Warning (FCW) sensor. To install the cover, follow these instructions:

1. Secure the top part of the cover so that it hinges on the header.
2. Swing the cover down and push on it so that it covers the opening.
3. Check to make sure the cover is secured properly.

NOTE

Be sure to remove the cover before returning the windshield to its normal position. Store the cover in the cargo area.

Cleaning Instructions

During windshield-down applications, dust/dirt can accumulate in the cover and block the camera lens. Use a microfiber cloth to clean the camera lens, module, and inside cover, being careful not to damage or scratch the module.

RAISING THE WINDSHIELD

1. Release the strap that secured the windshield in the lowered position.
2. Raise the windshield.
3. Using the provided #40 Torx head driver, reinstall the four Torx screws located along with the interior of the windshield. Secure them until they are snug, being careful not to cross-thread the screws or overtighten.
   1. Outside Torx Screws
   2. Inside Torx Screws
4. Reinstall the windshield wiper arms using the provided 15 mm socket. First, align the tips of the blade to the “T” mark in the glass. Then, while holding the arm in that position, reinstall the hex nut and tighten until snug. Be careful not to overtighten. Repeat for the other arm.
5. Reinstall the protective caps over the wiper arm hex bolts and push gently until they snap into place.
   1. Hex Bolt Cover Installed
   2. Hex Bolt Cover Removed
6. After completing the steps above:
   1. If your vehicle is equipped with a Soft Top, reinstall the Door Rails and raise the top.
   2. If your vehicle is equipped with a Hard Top, reinstall the Freedom Panels