XF

2022 Jaguar XF Windows Owners Manual

2022 Jaguar XF Windows

ELECTRIC WINDOWS

WARNING

Make sure to remove the smart key when leaving the vehicle. Remove of the smart key prevents unsupervised operation of the windows and sunroof, which may result in an injury.

  1. Rear window isolator button and child safety locks. See CHILD SAFETY LOCKS.
    WARNING

    If children are carried in the rear seats, the isolator switch should be used to prevent operation of the windows. If the windows are operated by young children, there is a risk of serious injury or death.

  2. Windows:

    Press the front of the switch to partially or fully open.

    Pull the front of the switch to partially or fully close.

    NOTES

    Each switch has a two-stage operation. Lightly press/pull and hold to manually operate to the required position. Alternatively, press/pull fully and release for one-touch automatic operation. One-touch automatic operation can be halted at any time, by operating the switch again.

    NOTES

    The windows operate for 5 minutes after the engine is switched off, as long as none of the doors are opened.

    NOTES

    If a resonance or a booming sound occurs when a rear window is open, lowering an adjacent front window by approximately 1 in (25 mm) eliminates the condition.

    CAUTION

    Any ice must be removed from the windows before operating. Ice on the window surface can cause damage to the operating mechanism.

  3. Sunroof button:
    NOTES

    The front and rear of the switch has a two-stage operation. Lightly press and hold to manually operate to the required position. Alternatively, press fully and release for one-touch automatic operation. One-touch automatic operation can be halted at any time, by pressing the switch again.

    With the sunroof closed, press the rear of the switch to partially or fully raise the sunroof to the tilt position. Press the rear of the switch again to partially/fully open the sunroof.

    NOTES

    If the sunroof blind is closed, the sunroof switch also opens the sunroof blind while operating the sunroof.

    With the sunroof open, press the front of the switch to partially or fully close the sunroof.

    CAUTION

    To prevent accidental damage, make sure any roof rack load does not interfere with the opening of the sunroof.

  4. Roof blind:
    NOTES

    The front and rear of the switch has a two-stage operation. Lightly press and hold to manually operate to the required position. Alternatively, press fully and release for one-touch automatic operation. One-touch automatic operation can be halted at any time, by pressing the switch again.

    Press the rear of the switch to partially or fully open.

    Press the front of the switch to partially or fully close.

    The roof blind can be opened whenever required, but it can only be closed when the sunroof is closed. If the sunroof is partially closed, the roof blind only partially closes to the same position. If the sunroof blind encounters a resistance when closing, it stops. Then, the blind either partially or fully opens, to allow removal of the obstruction and to prevent personal injury or damage to the mechanism. Press and hold the front of the switch, within 10 seconds of the partial or full opening, to override.

  5. Rear sunblind button:

    Press the switch to deploy.

    Press the switch again to store.

GESTURE ROOF BLIND

NOTES

The gesture roof blind feature works only when the ignition is switched on, or when the engine is running.

NOTES

The feature works in parallel with the overhead console’s roof blind buttons.

If the feature is fitted to the vehicle, there is a sensor system behind the overhead console which has two operating zones.

  • To open the blind, make a rearward swipe gesture with the hand, as illustrated at (1). Repeat the motion to stop movement of the roof blind.
  • To close the blind, make a forward swipe gesture with the hand, as illustrated at (3).
NOTES

The swipe gesture must pass through both sensor zones as illustrated at (2). A valid gesture cannot start or finish between the zones.

The gesture roof blind feature can be enabled or disabled by a retailer/authorized repairer.

WINDOW ANTI-TRAP PROTECTION

WARNING

Before closing a window or the sunroof, make sure that no occupants have any body part in a position where it could be trapped. Even with an anti-trap system, death or serious injury could occur.

Anti-trap protection is designed to stop window movement if an obstruction or resistance is detected. Check the window and its aperture. Remove any obstructions. The override procedure is as follows:

  1. Attempt to close the window. Anti-trap prevents closure and lowers the window.
  2. Within 10 seconds, attempt to raise the window again. Anti-trap prevents closure and lowers the window.
  3. Attempt to close the window for a third time, this time holding the switch in the close position. The window raises while the switch is held. Hold until closed.
NOTES

If this procedure fails to remove the blockage, or if the windows do not operate correctly, the window operation may need to be reset. See WINDOW RESET.

SUNROOF ANTI-TRAP MECHANISM

WARNING

Before closing a window, the sunroof, or the roof blind, make sure that no occupants have any body part in a position where it could be trapped. Even with an anti-trap system, death or serious injury could occur.

To prevent serious personal injury or damage to the vehicle, the sunroof and roof blind have an anti-trap mechanism. If the sunroof or the roof blind encounters a resistance when closing, it stops. Dependent on the sunroof’s or the roof blind’s current position, the sunroof or the roof blind partially or fully opens to allow the removal of any obstruction. Lightly press and hold the front of the switch to the first position, within 10 seconds of the partial or full opening, to override the anti-trap mechanism.

If the sunroof or the roof blind fails to operate correctly, it may need to be reset. See SUNROOF RESET.

SOLAR ATTENUATING GLASS

The solar attenuating glass windshield filters sunlight passing through a special laminated layer.

Electronic actuating cards, such as toll road payment cards or Radio Frequency (RF) ID tags, can be fixed at the dedicated locations. The locations are on the inside of the windshield. If the cards are located at any other part of a solar attenuating windshield, the electronic scanners may not recognise them.

The optimal fixing location is at the top of the windshield, as shown at (1), close to the interior rear-view mirror.

NOTES

The electronic actuating card should be in the size appropriate location on the driver’s side of the windshield.

NOTES

Transponders, mounted on the front license plate plinth, can be used as an alternative, dependent on the market and availability.

Automotive Solutions

Recent Posts

VW Jetta Engine Fuse Box Diagram

Access the comprehensive 2010-2018 VW Jetta Passenger Fuse Box Diagram to troubleshoot electrical issues effectively.…

8 months ago

VW Jetta Passenger Fuse Box Diagram

Explore the comprehensive VW Jetta Passenger Fuse Box Diagram to troubleshoot electrical issues effectively. Understand…

8 months ago

2023 Ford F-150 Lightning Fuse Box Diagram

Under Hood Fuse Box Location Remove the front luggage compartment cover. Under Hood Fuse Box…

2 years ago

2022 Kawasaki NINJA H2 SX SE Brake Lever Adjuster Owner’s Manual

2022 Kawasaki NINJA H2 SX SE Brake Lever Adjuster Owner's Manual NOTICE Only adjust the front…

2 years ago

2023 Land Rover Range Rover Evoque Exiting The Vehicle Owners Manual

2023 Land Rover Range Rover Evoque Exiting The Vehicle SINGLE LOCKING WARNING Before exiting the…

2 years ago

2023 Land Rover Range Rover Evoque Front Seats Owners Manual

2023 Land Rover Range Rover Evoque Front Seats FRONT SEAT SAFETY Make sure to read…

2 years ago