Do not use the Radio Frequency (RF) transceiver with any garage door opener that lacks the safety stop and reverse feature, as required by safety standards. A closing garage door may cause serious injury or death.
Do not use the RF transceiver with any garage door opener that was manufactured before April 1982. An outdated garage door opener can lead to malfunction of the garage door, potentially causing serious injury or death.
When programming the transceiver to a Garage door opener or entry gate, make sure the area is clear. This will prevent potential harm or damage as the gate or garage door will activate during the program.
Do not attempt to program the garage door opener with the vehicle inside the garage.
The system may suffer from interference if operated in the vicinity of a mobile or fixed station transmitter. Interference is likely to affect the hand-held transmitter, as well as the RF transceiver.
See INFORMATION AND ASSISTANCE.
Unplug the remote device during programming of the remote device if the repeated operation of the remote control is required. Repeated operation of the remote control during programming may result in damage to the remote device.
The instructions below apply to the majority of HomeLink compatible systems. However, there are some HomeLink applications, or HomeLink compatible systems, that require slightly different instructions. For more information and instructional videos, visit www.HomeLink.com.
Garage door openers manufactured after 1995 may be equipped with rolling code protection. If this is the case, a stepladder may be required to reach the learn or smart button.
If required, erase the previous programming from the HomeLink device. See TO ERASE ALL PROGRAMMING.
To program the HomeLink device:
Some remote device systems require the operator to cycle the remote control button every 2 seconds during programming. Refer to the additional information in Gate operator and Canadian programming at the end of the PROGRAMMING instructions.
The learn or smart button can usually be found directly on the motor-head unit. If in doubt, refer to the garage door opener’s manual to identify the button.
Canadian Radio Frequency (RF) laws require remote device systems to have a remote control signal that only operates for a short period of time. The signal times out before programming is complete. The operator is required to cycle the remote control button every 2 seconds during programming. Some U.S. gate operators also have this type of signal.
If in Canada, or experiencing difficulties while programming the remote device, carry out the following:
During programming of the remote device, replace programming step 3 with the following:
If the HomeLink LED indicator does not rapidly flash green or continuously illuminates green after performing these steps, contact HomeLink at: www.HomeLink.com. HomeLink is a registered trademark of Gentex Corporation.
To program a remote device to a previously programmed HomeLink button:
HomeLink is a registered trademark of Gentex Corporation.
To erase all programming from the HomeLink device:
Do not press and hold the buttons for longer than 20 seconds.
HomeLink is a registered trademark of Gentex Corporation.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
If the vehicle is sold, it is recommended that all programming is erased from the HomeLink device. See TO ERASE ALL PROGRAMMING.
Retain the original remote device’s remote control handset for future programming requirements.
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
For information on the range of compatible remote devices, or for assistance, contact a retailer/authorized repairer. Alternatively, visit the HomeLink website: www.HomeLink.com, or call the toll-free helpline at 1-800-355-3515.
For Genie and Sommer garage door openers, go directly to the HomeLink website.
HomeLink is a registered trademark of Gentex Corporation.
Access the comprehensive 2010-2018 VW Jetta Passenger Fuse Box Diagram to troubleshoot electrical issues effectively.…
Explore the comprehensive VW Jetta Passenger Fuse Box Diagram to troubleshoot electrical issues effectively. Understand…
Under Hood Fuse Box Location Remove the front luggage compartment cover. Under Hood Fuse Box…
2022 Kawasaki NINJA H2 SX SE Brake Lever Adjuster Owner's Manual NOTICE Only adjust the front…
2023 Land Rover Range Rover Evoque Exiting The Vehicle SINGLE LOCKING WARNING Before exiting the…
2023 Land Rover Range Rover Evoque Front Seats FRONT SEAT SAFETY Make sure to read…