2022 Hyundai Tucson Light Bulb Replacement User Manual

Hyundai logo

2022 Hyundai Tucson Light Bulb Replacement

2022 Hyundai Tucson product

LIGHT BULBS

We recommend that you consult an authorized HYUNDAI dealer to replace most vehicle light bulbs. It is difficult to replace vehicle light bulbs because other parts of the vehicle must be removed before you can get to the bulb. This is especially true for removing the headlamp assembly to get to the bulb(s). Removing/installing the headlamp assembly can result in damage to the vehicle.

WARNING

  • Prior to working on a light, depress the foot brake, shift to P (Park), apply the parking brake, press the Engine Start/Stop button to the OFF position and take the key with you when leaving the vehicle to avoid sudden movement of the vehicle and to prevent possible electric shock.
  • Be aware the bulbs may be hot and may burn your fingers.
    NOTICE
    Be sure to replace the burned-out bulb with one of the same wattage ratings. Otherwise, it may cause damage to the fuse or electrical wiring system.
    NOTICE
    To prevent damage, do not clean the headlamp lens with chemical solvents or strong detergents.

Information – Headlamp desiccant (if equipped)

This vehicle is equipped with desiccant to reduce fogging inside the headlamp due to moisture. The desiccant is consumable and its performance may change based on the used period or environment. If fogging inside the headlamp due to moisture continues for a long time, we recommend that you consult an authorized HYUNDAI dealer.

Information

The headlamp and tail lamp lenses could appear frosty if the vehicle is washed afterdriving or the vehicle is driven at night in wet weather. This condition is caused by the temperature difference between the lamp inside and outside and, it does not indicate a problem with your vehicle. When moisture condenses in the lamp, it will be removed after driving with the headlamp on. The removable level may differ depending on lamp size, lamp position and environmental condition. However, if moisture is not removed, we recommend that your vehicle is inspected by an authorized HYUNDAI dealer.

Information

  • A normally functioning lamp may flicker momentarily to stabilize the vehicle’s electrical control system. However, if the lamp goes out after flickering momentarily, or continues to flicker, we recommend the system be checked by an authorized HYUNDAI dealer.
  • The position lamp may not turn on when the position lamp switch is turned on, but the position lamp and headlamp switch may turn on when the headlamp switch is turned on. This may be caused by network failure or vehicle electrical control system malfunction. If this occurs, we recommend the system be checked by an authorized HYUNDAI dealer.

Information

The headlamp aiming should be adjusted after an accident or after the headlamp assembly is reinstalled.
Headlamp, position lamp, turn signal lamp, Daytime Running Light (DRL) replacement ONX4090022N

Light bulbs fig 1

  1. Headlamp (Low)
  2. Head lamp (High)
  3. Daytime running light/ Position light
  4. Turn signal lamp
  5. Side marker

If the LED lamp does not operate, we recommend that the system be inspected by an authorized HYUNDAI dealer. The LED lamps cannot be replaced as a single unit because it is an integrated unit. The LED lamps have to be replaced with the unit. A skilled technician should check or repair the LED lamp, for it may damage related parts of the vehicle.

Side repeater lamp replacement

Light bulbs fig 2

  • If the LED lamp (1) does not operate, we recommend that the system be inspected by an authorized HYUNDAI dealer.
  • The LED lamps cannot be replaced as a single unit because it is an integrated unit. The LED lamps has to be replaced with the unit.
  • A skilled technician should check or repair the LED lamp, for it may damage related parts of the vehicle.

Rear combination lamp replacement
Type A
Light bulbs fig 3
Type B

Light bulbs fig 4

  1. Tail lamp
  2. Tail/Stop lamp
  3. Turn signal lamp
  4. Reverse lamp
  5. Rear side marker

Light bulbs fig 5

Stop/Tail lamp (Outside)

  1. Turn off the engine.
  2. Open the liftgate.
  3. Loosen the lamp assembly retaining screws with a cross-tip screwdriver.
  4. Remove the rear combination lamp assembly from the body of the vehicle.
  5. Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly
    Light bulbs fig 6
  6. Remove the bulb from the socket by pressing it in and rotating itcounterclockwise until the tabs on the bulb align with the slots in the socket. Pull the bulb out of the socket.
  7. Insert a new bulb by inserting it into the socket and rotating it until it locks into place.
  8. Install the socket into the assembly by aligning the tabs on the socket with the slots in the assembly. Push the socket into the assembly and turn the socket clockwise.
  9. Reinstall the lamp assembly to the body of the vehicle.

Light bulbs fig 7

Tail lamp (Inside)

  1. Turn off the engine.
  2. Open the liftgate.
  3. Remove the service cover using a flat-blade screwdriver.
  4. Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.
    Light bulbs fig 8
  5. Remove the bulb from the socket by pressing it in and rotating it counterclockwise until the tabs on the bulb align with the slots in the socket. Pull the bulb out of the socket.
  6. Insert a new bulb by inserting it into the socket and rotating it until it locks into place.
  7. Install the socket into the assembly by aligning the tabs on the socket with the slots in the assembly. Push the socket into the assembly and turn the socket clockwise.
  8. Reinstall the lamp assembly to the body of the vehicle.

Turn signal lamp/Reverse lamp

  1. Turn off the engine.
  2. Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.
  3. Remove the bulb from the socket by pressing it in and rotating it counterclockwise until the tabs on the bulb align with the slots in the socket. Pull the bulb out of the socket.
  4. Insert a new bulb by inserting it into the socket and rotating it until it locks into place.

Light bulbs fig 9 Light bulbs fig 10

Stop&Tail lamp/Rear side marker (LED type)

  • If the LED lamp does not operate, we recommend that the system be inspected by an authorized HYUNDAI dealer.
  • The LED lamps cannot be replaced as a single unit because it is an integrated unit. The LED lamps has to be replaced with the unit.
  • A skilled technician should check or repair the LED lamp, for it may damage related parts of the vehicle.

High mounted stop lamp replacement

Light bulbs fig 11

  • If the LED lamp (1) does not operate, we recommend that the system be inspected by an authorized HYUNDAI dealer.
  • The LED lamps cannot be replaced as a single unit because it is an integrated unit. The LED lamps has to be replaced with the unit.
  • A skilled technician should check or repair the LED lamp, for it may damage related parts of the vehicle.

License plate lamp replacement

Light bulbs fig 12

  1. Using a flat-blade screwdriver, gently pry the lens cover from the lamp housing.
  2. Remove the bulb by pulling it straight out.
  3. Install a new bulb.
  4. Reinstall in the reverse order.

License plate lamp (LED type)

  • If the LED lamp does not operate, we recommend that the system be inspected by an authorized HYUNDAI dealer.
  • The LED lamps cannot be replaced as a single unit because it is an integrated unit. The LED lamps has to be replaced with the unit.
  • A skilled technician should check or repair the LED lamp, for it may damage related parts of the vehicle.

Interior light replacement

Map/Personal lamp (LED)

Light bulbs fig 13 Light bulbs fig 14

If the LED lamp does not operate, we recommend that the system be inspected by an authorized HYUNDAI dealer.
The LED lamps cannot be replaced as a single unit because it is an integrated unit. The LED lamps has to be replaced with the unit.
A skilled technician should check or repair the LED lamp, for it may damage related parts of the vehicle.

Map lamp, Room lamp, Sunvisor lamp and Luggage compartment lamp (Bulb type)

Light bulbs fig 15

  1. Using a flat-head screwdriver, gently pry the lens from the interior light housing.
  2. Remove the bulb by pulling it straight out.
  3. Install a new bulb into the socket.
  4. Align the lens tabs with the interior light housing notches and snap the lens into place.

NOTICE
Be careful not to damage the cover, tab, and plastic housing.

Leave a Comment