Tucson

2022 Hyundai Tucson Exterior Features User Manual

Contents hide

1 2022 Hyundai Tucson Exterior Features

2 EXTERIOR FEATURES

2.1 Hood

2.2 Liftgate

2.3 Smart liftgate (if equipped)

2.4 Liftgate open / close (Power liftgate)

2.5 Fuel filler door

2022 Hyundai Tucson Exterior Features

EXTERIOR FEATURES

Hood

Opening the hood

Park the vehicle and set the parking brake.
Pull the release lever to unlatch the hood. The hood should pop open slightly.
Go to the front of the vehicle, raise the hood slightly, push up the secondary latch (1) inside of the hood center and lift the hood.
Pull up on the hood support rod.
Install the end of the hood support rod into the slot located on the hood (3).

WARNING

Grasp the hood support rod in the area wrapped in rubber when the engine is hot. The rubber portion will insulate the heat and protect you from burn or injury.
The end of the hood support rod must be inserted fully into the hood slot whenever you inspect the engine compartment. This will prevent the hood from falling and possibly injuring you.

Closing the hood

Before closing the hood, check-in and around the engine compartment to ensure the following:
1. Any tools or other loose objects are removed from the engine room area or hood opening area
2. All glove, rags, or other combustible material is removed from the engine compartment
3. All filler caps are tightly and correctly installed
Return the hood support rod to its clip to prevent it from rattling.
Lower the hood until it is about 30 cm (12in.) above the closed position and let it drop. Make sure that it locks into place.
Check that the hood has engaged properly. If the hood can be raised slightly, it is not properly engaged. Open it again and close it with a little more force.

WARNING

Before closing the hood, ensure all obstructions are removed from around the hood opening.
Always double-check to be sure that the hood is firmly latched before driving away. Check there is no hood open warning light or message displayed on the instrument cluster. Driving with the hood opened may cause a total loss of visibility, which might result in an accident.
Do not move the vehicle with the hood in the raised position, as vision is obstructed, which might result in an accident, and the hood could fall or be damaged.

Liftgate

Opening the liftgate

Make sure the vehicle is in P (Park) and set the parking brake. Then do one of the following:

Unlock all doors with the Door Unlock button on your remote key or smart key. Press the liftgate handle button and open the liftgate.
Press and hold the liftgate open button on the remote key or smart key. Press the liftgate handle button and open the liftgate.
With the Smart Key in your possession, press the liftgate handle button and open the liftgate.

Closing the liftgate

Lower the liftgate lid and press down until it locks. To be sure the liftgate lid is securely fastened, always check by trying to pull it up again without pressing the liftgate handle button.

WARNING

Always keep the liftgate completely closed while the vehicle is in motion. If it is left open or ajar, poisonous exhaust gases containing carbon monoxide (CO) may enter the vehicle and serious illness or death may result.

NOTICE

To prevent damage to the liftgate support struts and the attached hardware, always close the liftgate before driving.

Information

In cold and wet climates, liftgate lock and liftgate mechanisms may not work properly due to freezing conditions.

WARNING

Do not grab or hold on to the liftgate support struts at any time. Damage to the liftgate support struts could result. Deformation of the liftgate support struts may cause vehicle damage and personal injury may occur.

WARNING

NEVER allow anyone to occupy the luggage compartment of the vehicle at any time. If the liftgate is partially or totally latched and the person is unable to get out, serious injury or death could occur due to lack of ventilation, exhaust fumes, rapid heat build-up, or because of exposure to cold weather conditions. The luggage compartment is also a highly dangerous location in the event of a crash because it is not a protected occupant space but is a part of the vehicle’s crush zone.
Your vehicle should be kept locked and keys should be kept out of the reach of children. Parents should teach their children about the dangers of playing in luggage compartments.

Emergency liftgate safety release

Your vehicle is equipped with the emergency liftgate safety release lever located on the bottom of the liftgate. When someone is inadvertently locked in the luggage compartment, the liftgate can be opened by moving the lever in the direction of the arrow and pushing the liftgate open.

WARNING

For emergencies, be fully aware of the location of the emergency liftgate safety release lever in the vehicle and how to open the liftgate if you are accidentally locked in the luggage compartment.
No one should be allowed to occupy the luggage compartment of the vehicle at any time. The luggage compartment is a very dangerous location in the event of a crash.
Use the release lever for emergencies only. Use with extreme caution, especially while the vehicle is in motion.

Power liftgate (if equipped)

The power liftgate open/close button automatically opens and closes the liftgate.
Before using the power liftgate The power liftgate operates when the gear is in P (Park) with the Engine Start/ Stop button in the ON position. However, the liftgate will operate regardless of the gear position when the engine is off. For safety, before attempting to open or close the liftgate, make sure the vehicle is in P (Park).

WARNING

Never leave children unattended in your vehicle. Children might operate the power liftgate. Doing so could result in injury to themselves or others and could damage the vehicle.
Make sure there are no people or objects around the liftgate before operating the power liftgate. Wait until the liftgate is opened fully and stopped before loading or unloading cargo or passengers from the vehicle.

NOTICE

Do not close or open the power liftgate manually. This may cause damage to the power liftgate. If it is necessary to close or open the power liftgate manually when the battery is discharged or disconnected, do not apply excessive force.

Opening the power liftgate

The power liftgate will open automatically by doing one of the following:

Press the liftgate button on the remote key or smart key for approximately one second.
Press the power liftgate button for approximately one second.
- To stop the operation of the power liftgate while it is in motion, quickly press the power liftgate button on the dash or on your remote key or smart key.
Press the liftgate handle button while having the smart key in your possession.

Closing the power liftgate

Press the liftgate open/close button on the key and hold until the liftgate is fully closed.
Releasing the liftgate open/close button on the key stops liftgate movement with the buzzer sound approximately for 5 seconds.
To stop the operation of the power liftgate while it is in motion, quickly press the power liftgate button on the dash or on your remote key or smart key.
To close the power liftgate from inside the vehicle, press and hold the Power Liftgate button on the dash. You must continue to hold the button until the liftgate is completely closed. The buzzer sounds continuously during the closing operation. If you release the button, the liftgate motion will stop and a continuous beeping will sound for about 5 seconds.
To stop the operation of the power liftgate while it is in motion, quickly press the power liftgate button on the dash or on your remote key or smart key.
Press the power liftgate inner button for approximately one second when the liftgate is opened. The liftgate will close and lock automatically.

NOTICE

Remain near your vehicle while closing the liftgate with the remote key or smart key.
If you exceed the distance limit of the smart key or remote key while the liftgate is in motion, the liftgate will stop and a continuous beeping will sound for about 5 seconds.

Automatic reverse

During power opening and closing if the power liftgate is blocked by an object or part of the body, the power liftgate will detect the resistance.

If the resistance is detected while opening the liftgate, it will stop and move in the opposite direction.
If the resistance is detected while closing the liftgate, it will stop and move in the opposite direction.

However, if the resistance is weak such as from an object that is thin or soft, or the liftgate is near the latched position, the automatic stop and reversal may not detect the resistance. If the automatic reversal feature operates continuously more than twice during opening or closing operation, the power liftgate may stop at that position. At this time, close the liftgate manually and operate the liftgate automatically again.

WARNING
Never intentionally place any object or part of your body in the path of the power liftgate to make sure the automatic reverse function operates.
NOTICE
Do not put heavy objects on the power liftgate before you operate the power liftgate. Additional weight may damage the operation of the system.

Non-operating conditions of the power liftgate

The power liftgate does not open when the vehicle is in motion.
- The chime will sound if you drive over 2mph (3km/h) with the liftgate open. Stop your vehicle immediately at a safe place and check if your liftgate is opened.
Operating the power liftgate more than 5 times continuously could cause damage to the operating motor. If this occurs, the power liftgate system enters into thermal protection mode to prevent the motor from overheating. In thermal protection mode, the power liftgate will not operate. If any of the power liftgate buttons are pressed to try to open the liftgate, the chime will sound 3 times but the liftgate will not operate. Allow the power liftgate system to cool for about 1 minute before operating the system again.
The power liftgate can be operated when the engine is not running. However, the power liftgate operation consumes large amounts of vehicle electric power. To prevent the battery from being discharged, do not operate it excessively e.g.: more than approximately 10 times repeatedly.
To prevent the battery from being discharged, do not leave the power liftgate in the open position for a long time.
When jacking up the vehicle to change a tire or repair the vehicle, do not operate the power liftgate. This could cause the power liftgate to operate improperly.
In cold and wet climates, the power liftgate may not work properly due to freezing conditions.

Resetting the power liftgate

If the battery has been discharged or disconnected, or if the power liftgate fuse has been replaced or removed, reset the power liftgate by performing the following procedure:

Put the gear in P (Park).
Press the power liftgate inner button (B) and the power liftgate handle switch (A) simultaneously for more than 3 seconds. The chime will sound.
Close the liftgate manually. If the power liftgate does not work properly after the above procedure, we recommend that the system be checked by an authorized HYUNDAI dealer.

Information

If the power liftgate does not operate normally, check again if the gear position is in the right position.

WARNING

Do not grab or hold on to the liftgate support struts at any time. Damage to the liftgate support struts could result. Deformation of the liftgate support struts may cause vehicle damage and personal injury may occur.
User Settings for the Power Liftgate From the Infotainment Screen The driver can select the power liftgate opening height or speed from the Settings menu in the infotainment system screen

Power liftgate opening height

To adjust the power liftgate opening height, select ‘Setup → Vehicle Settings → Door/Liftgate → Power Liftgate Opening Height → Full Open/Level 3/Level 2/Level 1/User Height Setting’.

See additional information in supplied Infotainment Manual

If ‘User Height Setting’ is selected, follow the instructions below to set the height of the power liftgate manually.

Position the liftgate manually to the height you prefer.
Press the power liftgate open/close button located inside the liftgate for more than 3 seconds.
Close the liftgate manually after hearing the buzzer sound.
The liftgate will open to the manually adjusted height that was set.

WARNING

Occupants should never ride in the rear cargo area where no restraints are available. To avoid injury in the event of an accident or sudden stops, occupants should always be properly restrained.

Emergency liftgate safety release

Your vehicle is equipped with the emergency liftgate safety release lever located on the bottom of the liftgate inside the vehicle.
When someone is inadvertently locked in the luggage compartment, the liftgate can be opened by moving the lever in the direction of the arrow and pushing the liftgate open.

WARNING

Be aware of the location of the emergency liftgate safety release lever in your vehicle and know how to open the liftgate using the safety release lever.
No one should be allowed to occupy the luggage compartment of the vehicle at any time. The luggage compartment is a very dangerous location in the event of a crash.
Use the release lever for emergencies only. Use extreme caution, especially while the vehicle is in motion.

Smart liftgate (if equipped)

On a vehicle equipped with a smart key, the liftgate can be opened with handsfree activation using the smart liftgate system.

Using smart liftgate

The hands-free smart liftgate system can be opened automatically when the following conditions are met:

The smart liftgate option is enabled in the Settings menu in the infotainment system screen.
The smart liftgate is activated and ready 15 seconds after all the doors are closed and locked.
The smart liftgate will open when the smart key is detected in the area behind the vehicle for 3 seconds.

Information

The smart liftgate will NOT operate when:

A door is not locked or closed.
The smart key is detected within 15 seconds from when the doors were closed and locked.
The smart key is detected within 15 seconds after the doors are closed and locked, and within 60 in. (1.5 m) from the front door handles. (for vehicles equipped with Welcome Light).
The smart key is in the vehicle.
Settings To activate the Smart Liftgate, go to User Settings Mode and select Smart Liftgate on the LCD display.
Detect and Alert The smart liftgate detecting area extends approximately 20~40 in. (50~100 cm) behind the vehicle. If you are positioned in the detecting area and are carrying the smart key, the hazard warning lights will blink and the chime will sound to alert you that the smart liftgate will open.
Information Do not approach the detecting area if you do not want the liftgate to open. If you have unintentionally entered the detecting area and the hazard warning lights and chime start to operate, move away from the area behind the vehicle with the smart key. The liftgate will remain closed.
Automatic opening After the hazard warning lights blink and the chime sounds 6 times, the smart liftgate will open.

Deactivating smart liftgate

Door lock
Door unlock
Liftgate open (Liftgate)

Liftgate open / close (Power liftgate)

If you press any button on the smart key during the Detect and Alert stage, the smart liftgate will be deactivated. Make sure to be aware of how to deactivate the smart liftgate for emergency situations.

If you press the door to unlock button (2), the smart liftgate will be deactivated temporarily. But, if you do not open any door for 30 seconds, the smart liftgate will be activated again.
If you press the liftgate open button (3) for more than 1 second, the liftgate opens.
The smart liftgate will still be activated if you press the door lock button (1) or liftgate open/close button (3) on the smart key as long as the smart liftgate is not already in the Detect and Alert stage.
In case you have deactivated the smart liftgate by pressing the smart key button and opening a door, the smart liftgate can be activated again by closing and locking all doors.

Detecting area

The smart liftgate detecting area extends approximately 20~40 in.(50~100 cm) behind the vehicle. If you are positioned in the detecting area and are carrying the smart key, the hazard warning lights will blink and the chime will sound for about 3 seconds to alert you that the liftgate will open.
The alert stops once the smart key is moved outside of the detecting area within the 3-second period. Information
The smart liftgate may not operate properly if any of the following occur:
- The smart key is close to a radio transmitter such as a radio station or an airport which can interfere with the normal operation of the transmitter.
- The smart key is near a mobile two-way radio system or a mobile phone.
- Another vehicle’s smart key is being operated close to your vehicle.
Smart liftgate detecting area may change when:
- The vehicle is parked on an incline or slope.
- One side of the vehicle is raised or lowered relative to the opposite side.

Fuel filler door

Opening the fuel filler door

Turn the engine off.
Ensure Driver’s door is unlocked.
Press the rear center edge of the fuel filler door.
Pull the fuel filler door (1) outward to access the fuel tank cap.
To remove the fuel tank cap (2), turn it counterclockwise. You may hear a hissing noise as the pressure inside the tank equalizes.
Place the cap on the fuel filler door.

Information

The fuel filler door will unlock when Driver’s door is unlocked.

To unlock the fuel filler door:

Press the unlock button on your smart key
Press the Central Door to unlock button on the armrest trim of the driver’s door The fuel filler door will lock when the Driver’s door is locked.

To lock the fuel filler door:

Press the lock button on your smart key
Press the Central Door lock button on the armrest trim of the driver’s door ÃÃAll doors will automatically lock after the vehicle speed exceeds 9 mph. The fuel filler door is also locked when the vehicle speed exceeds 9 mph.

Information

If the fuel filler door does not open because ice has formed around it, tap lightly or push on the door to break the ice and release the door. Do not pry on the door. If necessary, spray around the door with an approved deicer fluid (do not use radiator antifreeze) or move the vehicle to a warm place and allow the ice to melt.

Closing the fuel filler door

To install the fuel tank cap, turn it clockwise until it “clicks” one time.
Close the fuel filler door until it is latched securely.

Information

To lock the fuel filler door, make sure the fuel filler door is completely closed. Press the LOCK button on the remote key or smart key to lock your vehicle. The fuel filler door will also lock.
Note that if the fuel filler door is not completely closed when the vehicle is locked, the fuel filler door will not be locked.

CAUTION

Make sure the fuel filler door is completely closed before driving through a car wash or operating a high pressure spray washer.

WARNING

Automotive fuel is highly flammable and explosive. Failure to follow these guidelines may result in SERIOUS

INJURY or DEATH

Read and follow all warnings posted at the gas station.
Before refueling, note the location of the Emergency Fuel Shut-Off, if available, at the gas station.
Before touching the fuel nozzle, you should eliminate the potential buildup of static electricity by touching a metal part of the vehicle, a safe distance away from the fuel filler neck, nozzle, or another gas source, with your bare hand.
Do not use mobile phones while refueling. Electric current and/or electronic interference from cellular phones can potentially ignite fuel vapors and cause a fire.
Do not get back into a vehicle once you have begun refueling. You can generate a buildup of static electricity by touching, rubbing, or sliding against any item or fabric capable of producing static electricity. Static electricity discharge can ignite fuel vapors causing a fire. If you must re-enter the vehicle, you should once again eliminate potentially dangerous static electricity discharge by touching a metal part of the vehicle, away from the fuel filler neck, nozzle, or another fuel source, with your bare hand.
When using an approved portable fuel container, be sure to place the container on the ground prior to refueling. Static electricity discharge from the container can ignite fuel vapors causing a fire. Once refueling has begun, contact between your bare hand and the vehicle should be maintained until the filling is complete.
Use only approved portable plastic fuel containers designed to carry and store fuel.
When refueling, always shift the gear to the P (Park) position, set the parking brake, and press the Engine Start/Stop button to the OFF position. Sparks produced by electrical components related to the engine can ignite fuel vapors causing a fire.
Do not use matches or a lighter and do not smoke or leave a lit cigarette in your vehicle while at a gas station, especially during refueling.
Do not over-fill or top-off your vehicle tank, which can cause fuel spillage.
If a fire breaks out during refueling, leave the vicinity of the vehicle, immediately contact the manager of the gas station and then contact the local fire department. Follow any safety instructions they provide.
If pressurized fuel sprays out, it can cover your clothes or skin and thus subject you to the risk of fire and burns. Always remove the fuel cap carefully and slowly. If the cap is venting fuel or if you hear a hissing sound, wait until the condition stops before completely removing the cap.
Always check that the fuel cap is installed securely to prevent fuel spillage in the event of an accident.

Information

Make sure to refuel your vehicle according to the “Fuel Requirements” section suggested in chapter 1.

NOTICE

Do not spill fuel on the exterior surfaces of the vehicle. Any type of fuel spilled on painted surfaces may damage the paint.
If the fuel filler cap requires replacement, we recommend that you use only a genuine HYUNDAI cap or the equivalent specified for your vehicle. An incorrect fuel filler cap can result in a serious malfunction of the fuel system or emission control system.

Automotive Solutions