2022 Kawasaki Z125 Pro Meter Instruments
Meter Instruments
Lower Meter Button- Upper Meter Button
- Tachometer
- Multifunction Meter
- Clock
- Gear Position Indicator
- Fuel Gauge
- Speedometer
- Multifunction Display
- Odometer
- Trip Meter A/B
When the ignition switch is turned on, all LCD functions are shown for a few seconds, then the multifunction meter turns to operational mode.
Indicators
- Fuel Level Warning Indicator
- Turn Signal Indicator (Green)
- High Beam Indicator (Blue)
- Neutral Indicator (Green)
- Engine Warning Indicator (Yellow)
- Battery Warning Indicator (Red)
Indicator Initial Operation
When the ignition switch is turned on, all indicators go on/off as shown in the table. If any indicator does not operate as shown, have it checked by an authorized Kawasaki dealer.
- When the ignition switch is turned on.
- After a few seconds
- When engine starts.
- Goes on.
- Goes off.
When Warning Indicators Go On or Blink
When warning indicators appear, there could be a problem with vehicle function. Follow the actions in the table after stopping the vehicle in a safe place. The numbers in this column correspond to reference numbers on page 45.
Other Indicators
Speedometer/Tachometer
A. Tachometer
B. Red Zone
C. Speedometer
Speedometer
The speedometer is digital and can be set for km/h or mph. The unit setting can be changed according to local regulations. Make sure the unit setting (km/h or mph) is correctly displayed before riding. Refer to the Unit Setting in the Display Setting section.
Tachometer
The tachometer shows the engine speed in revolutions per minute (r/min, rpm).
NOTICE
Engine speed should not be allowed to enter the red zone; operation in the red zone will overstress the engine and may cause serious engine damage. When the ignition switch is turned on, the tachometer needle momentarily sweeps from the minimum to the maximum reading, then back the minimum reading to check its operation. If the tachometer does not operate correctly, have it checked by an authorized Kawasaki dealer.
Display Setting
Multifunction Display
WARNING
For Safety, do not operate the meter buttons while riding the motorcycle
Push the upper meter button to select the display modes. The display modes can be shifted in the following order.
NOTE
The multifunction display is dis- played in the unit depending on the unit mode setting.
A. Upper Meter Button
B. Flow when pushing the upper meter button
Odometer
The odometer shows the total distance. This meter cannot be reset.
NOTE
When the figures come to 999999, the display is stopped and locked
Trip Meter
To reset the trip meter:
- Push the upper meter button to dis-play the trip meter A/B.
- Push the lower meter button and hold it in until the display turns to 0.0.
NOTE
When the trip meter reaches 9999.9 while riding, the meter resets to 0.0 and continues counting.
Clock
To adjust the clock:
- Push the upper meter button to display the odometer.
- Push the lower meter button and hold it until both the hour and minute dis- plays blink.
- Push the lower meter button to select the hour or minute digits.
- Push the upper meter button to adjust the hour or minute digits.
- To finish the adjustment, push the upper meter button when both the hour and minute digits blink.
NOTE
When the battery is disconnected, the clock is reset to 1:00 and starts working again when the battery is connected.
Unit Setting
The unit setting in the meter instrument can be changed according to local regulations. Make sure the unit setting is correctly displayed before riding.
A. mph or km/h Display
B. mile or km Display
NOTE
Do not operate the motorcycle with the wrong unit (mph or km/h) of the speedometer.
To change the unit:
- Push the upper meter button to display the odometer.
- Push the lower meter button while pushing the upper meter button to select the display unit.
Features
Fuel Gauge
The fuel level in the fuel tank is shown by the number of segments displayed between E (empty) and F (full).
A. Segments
B. E (Empty)
C. F (Full)
NOTE
- When the fuel tank is full, all the segments are displayed. As the fuel level in the tank goes down, the segments disappear one by one from F (full) to E (empty).
- When the fuel level warning indicator and segment(s) blink, refer to the “When Warning Indicators Go On or Blink” in the Indicators section in this chapter.
Gear Position Indicator
This display shows the corresponding gear position when the transmission is shifted. As the transmission is shifted, the corresponding gear position (1st 4th) is shown in this display. When the transmission is in neutral, the neutral indicator goes on.
A. Gear Position Indicator
B. Neutral Indicator
NOTE
If the gear position display in the multifunction meter shows ” the transmission is not properly shifted to 1st. Be sure to shift the transmission.