2022 XC60 Volvo Starting and switching off the car Owners Manual

volvo logo

2022 XC60 Volvo Starting and switching off the car

2022-XC60-Volvo-Product-Image

Immobiliser

The electronic immobiliser is a theft protection system that prevents an unauthorised person from starting the car.

The car can only be started with the correct key.

The following error message in the driver display is related to the electronic immobiliser:

Symbol Message Specification
2022 XC60 Volvo Starting and switching off the car-Fig-01
The car key is not detected. See Owner’s Manual for more information. Error reading the key during starting – place the key on the key symbol in the cup holder and try again.

Starting the car

The car is started using the ignition dial in the tunnel console when a key is in the car.

WarningBefore starting:
  • Fasten the seatbelt.
  • Adjust the seat, steering wheel and mirrors.
  • Make sure that the brake pedal can be fully depressed.
2022 XC60 Volvo Starting and switching off the car-Fig-02
  • Start knob in the tunnel console.
  • Make sure the key is in the car.
  • Put the seatbelt on.
  • Depress the brake pedal.
  • Turn the start knob clockwise and release it.
    • The car starts and the ignition dial automatically returns to its original position.
  • Change gear to D or R.
NoteFor diesel-engined cars, there may be a slight delay before starting is initiated.
ImportantIf the engine fails to start after 3 attempts – wait for 3 minutes before making a further attempt. Starting capacity increases if the battery is allowed to recover.

When the engine is started, the starter motor works until the engine is started or until its overheating protection triggers.

Error messages

If the message Car key not detected is shown, place the key by the back-up reader. Then try to start the car again.

2022 XC60 Volvo Starting and switching off the car-Fig-03Backup reader’s location in the tunnel console.
NoteWhen the key is positioned by the back-up reader, make sure that there are no keys, metal objects or electronic apparatus by the back-up reader, (e.g. mobile phones, tablets, computers or chargers). Several keys close to one another by the back-up reader may cause interference with each other.
WarningNever remove the key from the car while driving or during towing.
WarningAlways take the key out from the car when leaving the car and make sure the car’s electrical system is in ignition position 0 – especially if there are children in the car.
NoteThe idling speed can be noticeably higher than normal for certain engine types during cold starting. This is done in order that the emissions system can reach normal operating temperature as quickly as possible, which minimises exhaust emissions and protects the environment.

Using jump starting with another battery

If the starter battery is discharged then the car can be started with current from another battery.

Jump starting requires access to another car’s 12 V battery as well as jump leads.

ImportantThe charging points in mild hybrid type cars are designed for only jump starting the car itself. Do not use the charging points of mild hybrids to start other cars – the fuse for the charging circuit may be overloaded so that it stops working.

In mild hybrid type cars, a discharged starter battery may be caused by an overloaded fuse which prevents charging. If the fuse has blown, the message 12 V battery fuse failure Service required is shown in the driver display. Volvo recommends that an authorised Volvo workshop is contacted.

2022 XC60 Volvo Starting and switching off the car-Fig-04Charging points for jump starting own car. The appearance in the engine compartment may vary depending on car model and equipment level.

When jump starting the car, the following steps are recommended to avoid short circuits or other damage:

  1. Set the car’s electrical system in ignition position 0.
  2. Check that the donor battery has a voltage of 12 V.
  3. If the battery is installed in another car – switch off its engine and make sure that the cars do not touch each other.
  4. Connect one of the red jump lead’s clamps to the donor battery’s positive terminal (1).
    Important
    Connect the jump lead carefully to avoid a short circuit and contact with other components in the engine compartment.
  5. Open the positive charging point’s cover (2).
  6. Attach the red jump lead’s other clamp onto the car’s positive charging point (2).
  7. Connect one of the black jump lead’s clamps to the donor battery’s negative terminal (3).
  8. Attach the black jump lead’s other clamp onto the car’s negative charging point (4).
  9. Check that the jump lead clamps are affixed securely so that there are no sparks during the starting attempt.
  10. Start the engine of the donor car and allow it to run for a few minutes at a rotation speed higher than normal idle approx. 1500 rpm.
  11. Start the engine in the car with the discharged battery.
ImportantDo not touch the connections between cable and car during the starting attempt. There is a risk of sparks forming.

Remove the jump leads in reverse order – first the black and then the red.

Make sure that neither of the black jump lead’s clamps comes into contact with the car’s positive charging point, the donor battery’s positive terminal, or the clamp connected to the red jump lead.

Warning48 V voltage can be dangerous in the event of incorrect intervention. Do not touch anything on the batteries that is not clearly described in the owner’s manual.
  • 48 V support battery must never be used for jump starting.
  • External electrical equipment must not, under any circumstances, be connected to the 48 V battery.
  • The 48 V battery may only be serviced and replaced by a workshop – an authorised Volvo workshop is recommended.
Warning
  • The battery can generate oxyhydrogen gas, which is highly explosive. A spark can be formed if a jump lead is connected incorrectly, and this can be enough for the battery to explode.
  • Do not connect the jump leads to any fuel system component or any moving part. Be careful of hot engine parts.
  • The battery contains sulphuric acid, which can cause serious burns.
  • If sulphuric acid comes into contact with eyes, skin or clothing, flush with large quantities of water. If acid splashes into the eyes – seek medical attention immediately.
  • Never smoke near the battery.
NoteIf the starter battery has such a low State Of Charge (SoC) that the car has no normal electrical functions and the engine is then jump-started with an external battery or a battery charger, the Start/stop function may continue to be activated. If the Start/stop function then auto-stops the engine shortly afterwards, there is a great risk that engine auto-start will fail because the battery has not had the time to recharge sufficiently.

If the car has been jump-started, or if there is insufficient time to charge the battery using a battery charger, the Start/stop function will be temporarily deactivated until the battery has been sufficiently recharged by the car. In an outside temperature of approx. +15 °C (approx. 60 °F), the battery needs to be charged for at least 1 hour by the car. In a lower outside temperature, the charging time may increase to 3–4 hours. The recommendation is to charge the battery if possible using an external battery charger.

Switching off the car

The car is switched off using the start knob in the tunnel console.

2022 XC60 Volvo Starting and switching off the car-Fig-05Start knob in the tunnel console.

To switch off the car:

  1. Turn the start knob clockwise and release it.
    • The car switches off and the ignition dial automatically returns to its original position.

If the gear selector is not in position P or if the car rolls:

Turn the ignition dial clockwise and hold until the car is switched off.

Ignition positions

The car’s electrical system can be set in different levels/positions and in this way make the different functions available.

In order to facilitate the use of a limited number of functions with the engine switched off, the car’s electrical system can be set in three different levels – 0I and II. These levels are described with the denomination “ignition position” throughout the owner’s manual.

The following table shows the functions available in each ignition position/level:

Level Functions
0
  • Odometer, clock and temperature gauge are illuminated.
  • Power seats can be adjusted.
  • The centre display is started and can be used.
  • The infotainment system can be used.

In this mode, the functions are controlled by time and are switched off automatically after a short while.

I
  • Panoramic roof, power windows, 12V power socket in the passenger compartment, Bluetooth, navigation, phone, ventilation fan and windscreen wipers can be used.
  • Power seats can be adjusted.
  • 12 V power sockets in the cargo area can be used.

Power is taken from the battery in this ignition position.

II
  • The headlamps come on.
  • Warning/indicator lamps illuminate for 5 seconds.
  • Several other systems are activated. However, heating in seat cushions and the rear window can only be activated after the car has been started.

This ignition position consumes a lot of current from the battery and should therefore be avoided!

Selecting ignition mode

The car’s electrical system can be set in different levels/positions and in this way make the different functions available.

Selecting ignition position

2022 XC60 Volvo Starting and switching off the car-Fig-06Start knob in the tunnel console.
  • Ignition position 0 – Unlock the car and store the key inside the car.
NoteTo reach level I or II without starting the engine – do not depress the brake pedal when these ignition positions are to be selected.
  • Ignition position I – Turn the start knob clockwise and release it. The control automatically returns to its starting position.
  • Ignition position II – Turn the start knob clockwise and hold it in position for approx. 5 seconds. Then release the knob, which automatically returns to its starting position.
  • Back to ignition position 0 – To return to ignition position 0 from position I and II – Turn the start knob clockwise and release. The control automatically returns to its starting position.

Leave a Comment