2023 Land Rover RANGE ROVER VELAR FRONT SEATS
FRONT SEAT SAFETY
Make sure that you have read and fully understood the following warnings before using any of the features in this section. Failure to observe cautions and warnings may result in vehicle damage, injury, or DEATH in the event of an accident.
WARNING
- Never adjust the driver’s seat while the vehicle is moving.
- Take care when retrieving items that have fallen down the side, back, front, or underneath the seat. Always stop the vehicle before retrieving items.
- Seat belts must be snug against the hips and chest to work properly. The more the seatback is reclined, the greater the chance of an occupant’s hips sliding under the lap section of the seat belt. The occupant’s neck could also strike the shoulder belt. Drivers and passengers should always sit well back in the seat, be properly belted, and have the seatbacks in an upright position.
- Make sure that the area immediately surrounding the seat is clear of obstructions before activating the seat memory function.
NOTES
Before attempting to perform any repairs on a vehicle, consult a retailer/authorized repairer.
Before attempting to perform any repairs on a vehicle, consult a retailer/authorized repairer.
ELECTRIC SEATS
WARNING
Make sure that you have read and fully understood the relevant warnings before using any of the features in this section. See FRONT SEAT SAFETY.
Make sure that you have read and fully understood the relevant warnings before using any of the features in this section. See FRONT SEAT SAFETY.
To adjust the seats, the smart key must be in the vehicle and the ignition switched on. Adjust the position of the electric front seats as follows:
- Cushion length.
- Bolster inflate and deflate.
- Lumbar support.
Press the top of the button to raise the lumbar support.
Press the bottom of the button to lower the lumbar support.
Press the front of the button to inflate the lumbar support.
Press the rear of the button to deflate the lumbar support.
- Head restraint height.
- Seatback angle.
- Seat height.
- Forward and rearward position.
- Cushion tilt.
The front head restraints can also be adjusted. See ELECTRIC FRONT HEAD RESTRAINTS.
RESTRICTED FRONT SEAT TRAVEL
WARNING
Make sure that you have read and fully understood the relevant warnings before using any of the features in this section. See FRONT SEAT SAFETY.
Make sure that you have read and fully understood the relevant warnings before using any of the features in this section. See FRONT SEAT SAFETY.
CAUTION
If seat movement stops unexpectedly during adjustment, check for, and remove any obstructions. An obstruction may cause damage to the seat mechanism. If front seat travel is restricted or obstructed, reset the seat adjustment mechanism, as follows:
If seat movement stops unexpectedly during adjustment, check for, and remove any obstructions. An obstruction may cause damage to the seat mechanism. If front seat travel is restricted or obstructed, reset the seat adjustment mechanism, as follows:
- Remove the obstruction.
- Adjust the seat to the point where movement stopped.
- Press and hold the switch for at least 2 seconds to override the restriction.
NOTES
If no obstructions can be seen, but normal adjustment cannot be carried out without stalling, contact a retailer/authorized repairer.
If no obstructions can be seen, but normal adjustment cannot be carried out without stalling, contact a retailer/authorized repairer.
SITTING IN THE CORRECT POSITION
WARNING
Make sure that you have read and fully understood the relevant warnings before using any of the features in this section. See FRONT SEAT SAFETY. The seat, head restraint, seat belt, and airbags all contribute to the protection of the user. Correct use of these components gives greater protection. Therefore, always observe the following points:
Make sure that you have read and fully understood the relevant warnings before using any of the features in this section. See FRONT SEAT SAFETY. The seat, head restraint, seat belt, and airbags all contribute to the protection of the user. Correct use of these components gives greater protection. Therefore, always observe the following points:
- Sit in an upright position, with the base of the spine as far back as possible. To achieve the optimum benefit of the seat belt in the event of an accident, do not recline the seat excessively.
- Do not move the driver’s seat too close to the steering wheel. Ideally, a minimum distance of 10 in (254 mm) is recommended between the breastbone and the airbag cover of the steering wheel. Hold the steering wheel in the correct position, with arms slightly bent.
- Adjust the head restraint so that the top of the head restraint is above the centerline of the head.
- Position the seat belt so that it is midway between the neck and shoulder. Fit the strap tightly across the hips, not across the stomach.
Make sure that the driving position is comfortable, enabling full control of the vehicle.
SEAT POSITION MEMORY
WARNING
Make sure that you have read and fully understood the relevant warnings before using any of the features in this section. See FRONT SEAT SAFETY. When a preferred seating position has been reached, the settings can be stored for future use. See ADJUSTING THE STEERING WHEEL and DOOR MIRRORS.
Make sure that you have read and fully understood the relevant warnings before using any of the features in this section. See FRONT SEAT SAFETY. When a preferred seating position has been reached, the settings can be stored for future use. See ADJUSTING THE STEERING WHEEL and DOOR MIRRORS.
- Press the memory store (M) button to activate the memory function.
- Press one of the preset buttons within 5 seconds to store the current settings. The message MEMORY (1, 2, or 3) SETTINGS SAVED displays in the instrument panel and a chime sounds to confirm the settings have been stored.
NOTES
A seat position only stores during the 5-second active period.
A seat position only stores during the 5-second active period.
NOTES
Any existing settings are over-written when storing a new memory position. Press the relevant preset button to recall a stored position. The message MEMORY (1, 2, or 3) SETTINGS RECALLED displays in the instrument panel to confirm the settings have been recalled.
Any existing settings are over-written when storing a new memory position. Press the relevant preset button to recall a stored position. The message MEMORY (1, 2, or 3) SETTINGS RECALLED displays in the instrument panel to confirm the settings have been recalled.