2022 Jeep Wrangler KEYS User Manual

2022 Jeep Wrangler KEYS

KEYS

KEY FOB

Your vehicle is equipped with a key fob that supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter ‘n Go™ (if equipped), and Remote Start (if equipped). The key fob allows you to lock or unlock the doors and swing gate from distances up to approximately 66 ft (20 m). The key fob does not need to be pointed at the vehicle to activate the system. The key fob also contains a mechanical key.

NOTE

• The key fob’s wireless signal may be blocked if the key fob is located next to a mobile phone, laptop, or another electronic device. This may result in poor performance.
• With the ignition on and the vehicle moving at 2 mph (4 km/h), all RKE commands are disabled.

WARNING

Push the Mechanical Key Release Button only with the key fob facing away from your body, especially your eyes and objects that may be damaged, such as clothing.

CAUTION

The electrical components inside of the key fob may be damaged if the key fob is subjected to strong electrical shocks. In order to ensure complete efficiency of the electronic devices inside of the key fob, avoid exposing the key fob to direct sunlight.

Key Fob

1. Mechanical Key Release Button
2. LED Indicator
3. Unlock Button
4. Remote Start Button
5.  Panic Button
6. Lock Button

NOTE

• In case the ignition switch does not change with the push of a button, the key fob may have a low or fully depleted battery. A low-key fob battery condition may be indicated by a message in the instrument cluster display, or by the LED light on the key fob. If the LED key fob light no longer illuminates from key fob button pushes, then the key fob battery requires replacement.
• Improper disposal of key fob batteries may be harmful to the environment. Please see an authorized dealer for proper battery disposal

To Lock/Unlock The Doors And Swing Gate

Push and release the unlock button on the key fob once to unlock the driver’s door, or twice to unlock all the doors and swing gate. To lock all the doors, push the lock button once. When the doors are unlocked, the turn signals will flash and the illuminated entry system will be activated. When the doors are locked, the turn signals will flash and the horn will chirp.

NOTE

All doors can be programmed to unlock on the first push of the unlock button through the Uconnect Settings Ú page 207.

Key Left Vehicle Feature

If a valid key fob is no longer detected inside the vehicle while the vehicle’s ignition system is in the ON/RUN or START position, the message “Key Fob Has Left The Vehicle” will be shown in the instrument cluster display along with an interior chime. An exterior audible and visual alert will also be activated to warn the driver. The vehicle’s horn will rapidly chirp three times along with a single flash of the vehicle’s exterior lights.

NOTE

• The doors have to be open and then closed in order for the vehicle to check for the presence of a key fob; the Key Left Vehicle feature will not activate until all of the doors are closed.
• These alerts will not be activated in situations where the vehicle’s engine is left running with the key fob inside.

Replacing The Battery In The Key Fob

The recommended replacement battery is CR2450.

NOTE

• Customers are recommended to use a battery obtained from Mopar®. Aftermarket coin battery dimensions may not meet the original OEM coin battery dimensions.
• Perchlorate Material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate for further information.
• Do not touch the battery terminals that are on the back housing or the printed circuit board.
• When a key fob battery is low, a warning will be indicated on the vehicle’s instrument cluster, and the fob LED will no longer illuminate with a button press.

1. Remove the back cover of the fob by inserting a flat-blade screwdriver into the slot on the bottom of the fob. Pry until the cover unsnaps being careful not to damage the seal. Proceed counterclockwise to pry the remaining snaps until the battery cover can be removed.
2. Remove the depleted battery by inserting a small flat-blade screwdriver into the battery removal slot and sliding the battery forward and up being careful not to damage the electronic board underneath.
3. Install the new battery into the key fob, making sure the positive (+) side is facing up. Slide the battery until it is seated securely below the tabs.
4. Reassemble the back cover making sure it is properly aligned before snapping it back in place.

WARNING

• The integrated key fob contains a coin cell battery. Do not ingest the battery; there is a chemical burn hazard. If the coin cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to death.
• If you think a battery may have been swallowed or placed inside any part of the body, seek immediate medical attention.
• Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children.

Programming And Requesting Additional Key Fobs

Programming the key fob may be performed by an authorized dealer.

NOTE

• Once a key fob is programmed to a vehicle, it cannot be repurposed and reprogrammed to another vehicle.
• Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle.

WARNING

• Always remove the key fobs from the vehicle and lock all doors when leaving the vehicle unattended.
• Always remember to place the Keyless Enter ‘n Go™ Ignition in the OFF position.

Duplication of key fobs may be performed at an authorized dealer. This procedure consists of programming a blank key fob to the vehicle electronics. A blank key fob is one that has never been programmed.

NOTE

• When having the Sentry Key Immobilizer System serviced, bring all vehicle keys with you to an authorized dealer.
• Keys must be ordered to the correct key cut to match the vehicle locks.