2023 Volvo V60 Maintenance and Service Owners Manual

The notification view shows when a new software update is available. You can choose when to install it after it has been downloaded. Update the software in the car as soon as possible when an update is available.

DownloadThe download takes place in the background via the mobile network when the car is running. It may take several hours, depending on the size of the update and the speed of the connection. If the car is switched off while the download is in progress, it is resumed automatically the next time the car is started.

• the car is connected to the Internet (Use of the Internet involves data transfer (data traffic), which may involve charges. Volvo meets the cost of data traffic for system updates unless a personal SIM card is installed).
• approval of the use of online services.

Installing an updateOnce a software update has been downloaded and is ready for installation, this is shown in the notification view and by a message when the car is started. You can choose to install the update immediately, or have a further reminder at a later date.

Always read through what the update contains so that you know how the car and its functions are affected.

If the installation fails, the car’s systems are reset to the latest installed version.

Information on contentsTap on the information symbol in the centre display for more information on the content of the software update.

NoteFunctionality after updating may vary depending on market, model, model year and options.

Brake system maintenance

Check brake system components regularly for wear.

To keep the car as safe and reliable as possible, follow the Volvo service intervals as specified in the Service and Warranty Booklet. After replacing brake linings and brake discs, the braking effect is only adopted after they have been “worn in” for a few hundred kilometers (miles). Compensate for the reduced braking effect by depressing the brake pedal harder. Volvo recommends only fitting brake linings that are approved for your Volvo.

ImportantThe wear on the brake system’s components must be checked regularly.

Contact a workshop for information about the procedure or engage a workshop to carry out the inspection – an authorized Volvo workshop is recommended.

Operational disruption

If you experience an operational disruption or deviation from the car’s normal function then it may be due to a fault or the specific circumstances of the situation.

Some functions have limitations in particular situations and require that certain conditions are fulfilled in order to work. The driver display and centre display may show messages in order to inform about such a situation.

Find out more about fault-tracing and the limitations of various functions in related articles below.

If the car is not drivableActivate the hazard warning flashers if the car has broken down or been forced to stop unexpectedly in a trafficked environment. Think about safety. If possible, move the car out of danger from traffic. Put on a reflective vest and then position the warning triangle so that other road users are warned in good time. Call roadside assistance if the cause cannot be remedied at your location.

Data transfer between car and workshop via Wi-Fi

Volvo’s workshops have a specific Wi-Fi network for data transfer between the car and the workshop. The car is connected using the key’s buttons, so it is important to take along a key with buttons in the event of a workshop visit.

During a workshop visit, your service technician can perform fault-tracing and update software via the network.

Connection with a keyPress three times on the lock button on the key to connect the car to the workshop’s network. Connection is normally handled by the service technician.

When the car is connected to a Wi-Fi network, the symbol appears in the center display.

It is not possible to use the key to connect to other Wi-Fi networks.

WarningThe car must not be driven when connected to the workshop’s networks and systems.

Raise the car

It is important to use the correct lifting points on the car’s chassis when using a jack (Option/accessory) to raise the car. Read through all of the instructions before raising the car.

Arrows along the bottom edge of the side of the car mark where the jacking points/lifting points (marked in red) are located.

NoteVolvo recommends only using the jack that belongs to the car model in question. If a jack is selected other than the one recommended by Volvo, follow the instructions supplied with the equipment.

ImportantIf a jack is included with the car, it is only designed for occasional, short-term use, such as when changing a wheel after a puncture. Only the jack belonging to the specific model is to be used to jack up the car. If the car is to be jacked up more often, or for a longer time than is required just to change a wheel, use of a garage jack is recommended. In this instance, follow the instructions for use that come with the equipment.

When the jack is not in use it should be stored in its storage space under the cargo area floor. Crank the jack down for it to fit.

Warning

• The car must not be allowed to roll while it is being raised. Apply the parking brake and set the gear selector in Park position (P).
• Chock in front of and behind the wheels that remain on the ground using solid wooden blocks or large stones.
• When changing a wheel, use a jack intended for the car model. Use additional stands to support the car for all other work.
• Do not use a jack in poor condition. Check that the threads are lubricated, and that it is free of damage and dirt.
• Check that the jack is stable. The surface underneath must be firm, flat and not slippery.
• Never position anything between the ground and the jack, or between the jack and the car’s lifting point.
• Never allow passengers to remain in the car while the car is being supported by the jack. Make sure that they are standing in a safe location if a wheel needs to be changed in a trafficked location.
• No part of your body may be extended under the car while it is raised on the jack.

WarningIf the car is lifted on a garage jack, the jack must be placed under the lifting points. Make sure that the jack is correctly positioned so that the car cannot slide off during lifting. Make sure the head of the jack is fitted with rubber guards so that the car remains stable and is not damaged. Always use axle stands or similar when the car is in the raised position.

When the jack is not in use it must be stored in its storage space.

Read through all instructions before beginning. Take out the tools needed before jacking up the car.

1. Set up the warning triangle and activate the hazard warning lights if, for example, a tyre is being changed in a trafficked location.
2. Apply the parking brake and engage gear position P.
   Note

   Applies to cars with level control:(Option/accessory) If the car is equipped with air suspension, this must be disabled before the car is raised.

3. Chock in front of and behind the wheels that remain on the ground. Use, for example, heavy wooden blocks or large stones.

    

4. Position the jack or the lift arms at the designated spots of the car’s undercarriage. The triangle markings in the plastic cover indicate the locations of the jacking/lifting points. There are two jacking points on each side of the car. There is a recess for the jack at each point.

5. Position the jack on level, firm and non-slippery ground under the jacking point that will be used.

    

6. Crank the jack up until it is correctly positioned and comes into contact with the car’s jacking point. Check that the head of the jack (or lifting arms at a workshop) is correctly positioned in the jacking point so that the bump in the centre of the head fits into the jacking point hole, and check that the base of the jack is positioned vertically below the jacking point.
7. Turn the jack so that the crank is as far away from the side of the car as possible, at which point the jack’s arms are perpendicular to the direction of the car.
8. Raise the car to the height required to perform the task.